Skip to main content

Garden Soil Calculator: Volume, Bags and Weight

Calculates garden soil or topsoil volume in m³ and tonnes, with equivalent 40 L bags and an optional cost estimate.

To fill a garden bed measuring 2 m × 3 m to a depth of 20 cm, you need 1.2 m³ of topsoil. That is 30 bags of 40 L, with a total mass of 1.32 tonnes. The same volume of universal potting mix weighs about 0.78 tonnes, a difference of 540 kg that changes how you plan the delivery.

Converting cubic metres to 40 L bags is direct, because 1 m³ equals 25 bags. Mass is where the numbers vary. Topsoil is typically about 1.1 t/m³, universal potting mix about 0.65 t/m³ and peat-based mix around 0.45 t/m³, but the real figure depends on moisture content and on the product, so use the supplier's data sheet when it gives one. Soil is heavy, so check the payload rating in your vehicle's handbook before you load it. For larger volumes, a bulk delivery by tipper truck is often the more practical option.

Enter the length and width of the area in metres, the depth of the layer in centimetres and the type of soil mix. The calculator returns the volume in m³, the number of 40 L bags and the total weight. You can also enter the price per m³ from a supplier quote, or leave it at 0 to skip the cost estimate.

Garden beds, lawns and vegetable patches each need a different depth, so the first decision is usually the layer depth. The sections below explain how to choose it, when bulk delivery makes sense and what to check before the truck arrives.

Bulk soil settles over the first few weeks, so order a little more than the calculated volume, and more again if you are using topsoil rather than bagged mix. Bagged potting mix compacts less and needs a smaller margin.

The result updates automatically.

For irregular beds, use the maximum dimension and scale the width proportionally.

Measure in a straight line, edge to edge.

Lawn: 4–6 in (about 10–15 cm) · Beds and shrubs: 8–12 in (about 20–30 cm) · Vegetable patch: 12–16 in (about 30–40 cm) · Trees: 16–24 in (about 40–60 cm)

This affects the total weight and reference price. Multi-purpose compost is the most common choice for home gardens.

Reference value for this type of substrate. Adjust to match the quote you've received. Enter 0 to ignore the cost.

Topsoil needed

4.00m³

Area: 20.00

Equivalent in 40 L bags

100bags

Approx. total weight: 2.60 t

Estimated material cost

$320.00

For 4.00 at $80.00

Area
20.00 m²
Topsoil volume
4.000 m³
40 L bags needed
100 bags
Estimated total weight
2.60 t

Turn this calculation into a quote for your client

We're building a tool for professionals. Be among the first to try it.

Share

How it works

1

Enter the length and width of the area to fill, in metres.

2

Set the layer depth: 10 to 15 cm for lawn, 20 to 30 cm for garden beds, 30 to 40 cm for a vegetable patch.

3

Choose the soil type, because it changes the total weight and the reference price.

Formula

V = C × L × (P ÷ 100) | S = ⌈V × 25⌉ | M = V × d
V — Volume of soil in m³
C — Length of the area (m)
L — Width of the area (m)
P — Depth of the layer (cm)
S — Number of 40 L bags (rounded up)
M — Total mass (t): volume × density of the soil mix
d — Density in t/m³ of the soil mix (planning values: topsoil ≈ 1.1 · universal potting mix ≈ 0.65 · peat ≈ 0.45; use the supplier's figure for its own product if available)
⌈⌉ — Rounded up: whole bags are always ordered

How the calculation works

How to calculate garden soil: volume, bags and weight

Preparing a garden area starts with working out how much soil you need. The most common mistake, and the most expensive, is underestimating the quantity, especially with bulk topsoil delivered by tipper truck. A second delivery costs about as much as the first, and it often arrives days later, when the site is already dug out.

The formula: simple, with one detail that matters

The volume of soil comes from three measurements: length, width and the depth of the layer you are adding. A vegetable patch 5 metres long and 4 metres wide, filled to 30 centimetres, needs 5 × 4 × 0.30 = 6 m³ of soil.

The calculator then converts that volume into 40 L bags, using 1 m³ = 25 bags, and rounds up so that you always order whole bags. The total mass is the volume multiplied by the density of the soil mix. Density is the detail people forget. Typical planning values are about 1.1 tonnes per cubic metre for topsoil and about 0.65 for universal potting mix, but a supplier's figure for its own product is more reliable. Mass affects the delivery, the number of trips and whether your trailer or ute is rated for the load.

Bags or bulk: which is more economical?

The choice between bags and bulk delivery usually depends on the quantity and on how easily a truck can reach the site. For volumes up to about 1 m³, 40 L bags are the practical option. They fit in a family car or a ute, you can work at your own pace, and any leftovers can be stored without trouble. The cost per cubic metre of bagged soil is, however, considerably higher than bulk.

From about 1.5 m³, bulk delivery starts to make economic sense. Topsoil from landscape supply yards and quarries arrives by tipper truck, and the price per cubic metre is usually well below the bagged equivalent, even after adding the delivery charge. For a 20 m² vegetable bed filled to 30 cm (6 m³ in total), the saving can be significant. Bulk soil is available from landscape supply yards and building materials suppliers, and sometimes from excavation sites. Soil taken from an excavation is not always suitable for a garden, because its origin and condition are unknown, so ask where it came from before you take any.

Bulk delivery also needs room. Confirm that the gate and driveway can take the truck, check whether the supplier will tip on the driveway or on the nature strip, and plan where the pile will sit while you spread it. A pile left on the lawn for a week can kill the grass underneath.

Soil types and what to choose for each situation

Three categories cover most of what is sold at landscape yards and garden centres.

Topsoil: natural soil that has been excavated or stockpiled, screened and sometimes blended with compost. It is the heaviest of the three and the cheapest in bulk. It suits filling large areas, preparing vegetable patches and levelling ground. Quality varies widely. Heavy clay drains slowly, while sandy soil dries out quickly and needs organic matter. Ask the supplier where the soil came from and what it contains. For vegetables, test the pH before planting, using the method set out in ISO 10390.

Universal potting mix: a blend of peat or coir, perlite, compost and slow-release fertiliser. It is lighter than topsoil, more porous and good at holding moisture. It is the most common choice for home gardens and the most balanced for garden beds, herbs and outdoor pots. Many mixes now use coir in place of peat, so check the label if that matters to you.

Premium or ericaceous mix: a higher proportion of peat or sphagnum with added micronutrients. It suits acid-loving plants such as azaleas, rhododendrons and blueberries, and high-yield pot cultivation. For an ordinary garden, the performance gain over a universal mix rarely justifies the extra cost.

The right depth for each planting type

The depth of new soil sets the quantity you need to order. For lawn grown from seed or laid as turf, 10 to 15 centimetres over prepared ground is enough for most common lawn species. For annual and perennial beds, 20 to 25 centimetres gives roots room to grow without reaching compacted native ground.

In a vegetable patch, 30 centimetres is the minimum for crops such as tomatoes, capsicum and zucchini. Carrots and other root crops need 40 to 50 centimetres of loose soil. In suburban backyards where the base is compacted clay or builders' rubble, raised beds with timber or brick edging are often easier than digging out the existing ground.

For shrubs and hedges such as lilly pilly, murraya or dwarf olive, 40 to 50 centimetres of good quality soil at planting time prevents root problems in the first years, especially in heavy clay.

Drainage and compaction: what the tables do not show

New soil placed over existing ground compacts over the first months. That is normal and expected. The problem arises when the base does not drain. Water collects at the boundary between the new soil and the old, causing waterlogging and root rot.

For heavy clay, the simplest fix is to loosen the base with a fork or ripper before adding the new layer. Alternatively, mix coarse washed river sand into the new soil. Use river sand, not sea sand, which contains salt. On sloping ground or in formal beds, a geotextile membrane laid at the base stops the two soils mixing without blocking drainage.

Common mistakes

  • Mixing up units. Length and width are entered in metres, while the depth is entered in centimetres. A 20 cm layer is entered as 20, not 0.2.
  • Measuring the outside of a raised bed. Measure the internal dimensions, because the edging takes up space that the soil does not fill.
  • Ordering by volume alone. Check the total mass against what your vehicle or trailer can carry, and plan trips accordingly.
  • Using topsoil in pots. Containers need a potting mix, because topsoil drains poorly and compacts in a small space.
  • Forgetting settling. A bed filled to exactly the calculated depth will look low after a few weeks. Allow a small margin.

Edge cases

A depth of zero gives zero volume, zero bags and zero mass, which is correct for a surface that is not being filled. A length or width of zero gives the same result. Negative dimensions have no physical meaning, so enter positive values only.

When to use this calculator, and when not to

Use it to size a fill for a garden bed, lawn base, vegetable patch or raised area, and to compare bagged and bulk options. Do not use it to design the garden, to work out drainage or to set levels for a slab. Larger projects, areas over 100 m², steep slopes, automatic irrigation systems and work that involves retaining walls are better handled by a qualified landscape architect or an experienced landscape designer. If a retaining wall is part of the plan, ask your local council whether approval is needed before you build.

Local norms and references

In Australia, soils used for landscaping and garden work are covered by AS 4419, Soils for landscaping and garden use. The standard is a useful reference when you ask a supplier for a product specification. The pH measurement method is set out in ISO 10390. Check your local council's website for any requirements that apply to deliveries or to the reuse of excavated material, and for any guidance it publishes on garden soil and mulch, before ordering a large delivery.

The weights used here are planning values, not figures taken from a published standard. Wet soil weighs more than dry, and each product differs. If your supplier gives a density for its own product, use it in place of the planning value, and expect the actual delivered weight to vary.

Practical checklist before you order

Measure the internal dimensions of the area, decide on the depth for the planting type, choose the soil type, and confirm the access and tipping location for any bulk delivery. Order a small margin above the calculated volume, and on arrival compare the delivered quantity with the delivery docket. Keep a record of the supplier and the quantity, because it makes any later top-up quicker to source and to match.

Frequently asked questions

How many 40 L bags of soil do I need per square metre of garden bed?

It depends on the depth you want. At 20 cm (a typical flower bed), each square metre needs 0.20 m³ of soil, which is 5 bags of 40 L. At 30 cm (a vegetable patch), each square metre needs 0.30 m³, which is 7.5 bags, so you round up to 8. Use this calculator with the real dimensions of your bed to get the exact number of bags for the whole area.

What is the difference between topsoil and universal potting mix for the garden?

Topsoil is natural soil, usually sold in bulk, and it is the heavier of the two, typically about 1.1 t/m³. It suits filling large areas and preparing vegetable patches or lawns. Universal potting mix is a blended product containing peat or coir, perlite, compost and fertiliser. It is lighter, typically about 0.65 t/m³, drains well and gives plants nutrients from the start, which makes it better for garden beds, herbs and outdoor pots. For large areas where cost matters most, bulk topsoil is usually the more economical choice.

How much does garden soil cost in Australia?

Prices vary by region, soil type and whether you buy in bags or in bulk. Bulk topsoil delivered by tipper truck is usually cheaper per cubic metre than bagged potting mix, and the gap grows with the volume you order. Bagged mix costs more per cubic metre but is easier to handle in small quantities. Get at least two quotes from local landscape supply yards, including delivery, and enter the price per m³ in the calculator to see the estimated cost.

How deep should the soil be for a new lawn?

For a lawn grown from seed, 10 to 15 cm of prepared soil over loosened ground is enough for most common lawn species. For turf laid on prepared ground, about 10 cm of levelled soil is generally sufficient. In heavy clay or very sandy ground, mix in washed river sand or compost in the base layer before adding the final soil, so that the lawn establishes evenly and drains properly.

Is it worth ordering bulk soil or is it better to buy bags?

For volumes up to about 1 m³, bags are more practical. They are easy to transport in a family car or ute, they can be stored without trouble and they do not need truck access. From about 1.5 m³, bulk delivery is usually more economical, and the difference per cubic metre can be large, especially for vegetable patches and bigger projects. Bulk delivery needs enough room for a tipper truck and a clear place to unload the pile. Check access before you book.

Why does the soil level drop a few weeks after I fill a bed?

New soil settles and compacts over the first months, as air is pushed out and the particles pack closer together. This is normal. Bulk topsoil settles more than bagged potting mix, so allow a small margin above the calculated volume. If the level keeps dropping or water pools on the surface, the problem may be the base rather than the settling. In that case, loosen the ground beneath the new layer or check the drainage before adding more soil.

When should I hire a landscape architect or designer?

For simple jobs, such as filling a garden bed, preparing a vegetable patch or sowing a lawn, this calculator and some careful reading are enough. A qualified landscape architect or an experienced designer is worth the cost when a project involves reshaping the ground on slopes, automatic irrigation, built-in paving or areas over 100 m². A professional can help avoid drainage errors, choose plants suited to the local climate and plan for long-term maintenance, which often costs less than correcting mistakes later.

View all Garden, Outdoor & Water calculators →

By RivoCalc · Reviewed under our editorial methodology · Updated 11 June 2026

This calculator is for information purposes only. Results are estimates based on standard formulas and may vary depending on real-world conditions. Consult a professional before making important decisions.