Roof Tile Calculator: How Many Tiles Do You Need?
Calculates the roof tiles needed for a pitched roof in Marseille, barrel, Roman or flat profiles, with a waste allowance and optional cost estimate.
Assuming a data-sheet yield of 16 pieces per m² for Marseille-profile tiles, covering 60 m² of sloped roof with a 10% waste allowance needs 1,056 tiles (60 × 16 × 1.10). The 16 pieces per m² is an example value, so replace it with the figure from your product's data sheet, and enter the sloped surface of the roof rather than its footprint on the plan.
The tile profile changes the count more than most people expect. Yield differs between profiles, so the same roof can need very different numbers of pieces, pallets and delivery trips. This calculator covers four clay profiles (Marseille, barrel, Roman and flat), with a starting yield already filled in for each one. Those starting values are not product specifications. For concrete, fibre-cement or any specific product, choose Custom and enter the yield from the manufacturer's data sheet.
Enter the real sloped area of the roof, the tile profile and the waste allowance. The calculator returns the total number of pieces, rounded up to a whole tile. If you also enter a price per piece, it estimates the material cost, which is useful for budgeting but is not a quote.
The area is the input that most often goes wrong. On a pitched roof, the sloped surface is larger than the footprint: at a 30% slope it is about 4.4% larger, and at 45% about 9.7% larger. On an 80 m² footprint, that gap is between 3.5 and 7.7 m², enough to leave a row of tiles short at the last section. Measure the sloped surface, or convert from the footprint and pitch using the method explained below.
The result is a material estimate for ordering and budgeting. It does not replace a roof design, a structural check or a municipal permit where one is required.
The explanation below uses metric units; the calculator works in either system.
The result updates automatically.
The actual sloped surface area, not the plan (footprint) area
Typical value for the selected roof tile type
10% for simple roofs; 15% for roofs with multiple pitches or complex ridge lines
Check the unit price with your supplier for the model you've chosen
Roof tiles needed
includes 128 pieces of waste allowance
- Roof area
- 80.0 m²
- Coverage rate
- 16 pieces per m²
- Tiles before allowance
- 1,280 pieces
How it works
Formula
How the calculation works
How many roof tiles do you need?
Replacing or installing a roof is one of the biggest jobs on a house, both for protection and for cost. Working out the tile count before you order avoids two common problems: running short partway through and waiting for a matching batch, or buying far more than you need. The formula is simple. Multiply the roof area by the number of pieces per square metre, then add a waste allowance. Most errors come from one mistake: using the footprint of the building on the plan instead of the real sloped surface of the roof.
How the formula works
The calculation is N = ⌈A × r × (1 + D/100)⌉. A is the sloped area in square metres. r is the tile yield in pieces per square metre. The term (1 + D/100) increases the total by the waste allowance D, given as a percentage. The ceiling symbol rounds the result up to a whole tile, because you cannot order part of a tile and a partial row still needs a full piece. Each input is a physical quantity: an area, a count per area and a percentage. Nothing else enters the result, so the answer is only as good as the area and the yield you enter.
Measuring the real roof area
The area that matters is the sloped surface, not the footprint. On a single roof plane, the slope length is longer than the horizontal run. For example, a plane 10 m long with a horizontal run of 5 m and a 35% pitch has a slope length of √(5² + 1.75²) ≈ 5.30 m, so its real area is 53 m², not the 50 m² shown on the plan.
If you know the footprint and the slope but not the sloped area, use this conversion:
Sloped area = Footprint × √(1 + (slope % / 100)²)
For a symmetric gable roof with an 80 m² footprint and a 35% slope, the sloped area is about 80 × 1.059 ≈ 85 m². If your pitch is given as a ratio of rise to run, such as 6 in 12, divide the rise by the run and multiply by 100 to get the slope in percent: 6 ÷ 12 × 100 = 50%.
On a roof with several planes, measure each plane separately and add the areas. For a complete replacement, a roofing contractor can measure the roof on site or from drawings. On new construction, the framing plans or the architect's drawings should give the sloped area of each plane.
Tile profiles and their yields
Clay tile profiles differ in size, lap and pieces per square metre, so the yield changes between them. Yields are set by the piece dimensions and the lap, and the manufacturer's data sheet gives the exact figure for a product. Use that figure rather than a general value, because it sets the real coverage.
Marseille: an interlocking flat tile, widely used on new roofs where clay tile is common. The mechanical interlock makes alignment faster.
Barrel tile (pan and cover): a two-piece profile with a curved pan and a cover, traditionally associated with older buildings and Mediterranean-style houses. Each course is made of two pieces, so the lap and the piece dimensions have a large effect on the count. Water has to drain between the pan and the cover, so the minimum pitch in the manufacturer's data is important.
Roman tile: similar in size to Marseille but with a gentler profile. It is most often seen on Mediterranean-style homes, and its yield should be taken from the data sheet like any other profile.
Flat tile: a small rectangular tile with a plain, austere look. Because each piece covers less of the roof, the piece count is much higher than for the larger profiles, and on a typical house it runs well into the thousands. A lower price per piece does not mean a lower cost per square metre, so compare quotes per square metre installed.
For concrete tile, fibre-cement tile or a specific product, choose Custom and enter the yield from the data sheet.
Waste allowance and rounding
The waste allowance covers three sources of loss. The first is cutting at the perimeter, especially at gables, hips and valleys. The second is breakage during transport and installation. The third is a reserve for future repairs. A simple roof with one plane and a rectangular outline usually needs about 10%. A roof with several planes, dormers, hips or valleys usually needs about 15%. Roofs with many irregularities or non-rectangular plans may need more, so review the allowance with your roofer.
Keeping a small stock of spare tiles in a dry place is worth the space. When a tile breaks years later, the same profile and batch may no longer be available, and a tile from another batch can differ in colour and surface. Buy the full count from one batch where possible.
When to use this calculator
Use it for early budgeting, for checking the quantities in a contractor's quote, and for ordering material on a simple roof with a known yield. It is also useful for comparing profiles. Changing the profile changes the number of pieces, and so the number of pallets and delivery trips, even when the roof area stays the same.
When not to use it
Do not rely on the calculator alone in these cases:
- Complex roofs with many hips, valleys, dormers or skylights. The contractor should take off quantities from a drawing.
- Asphalt shingles, which are normally sold and counted in bundles. Use the manufacturer's coverage per bundle instead.
- Structural decisions. Rafters, battens, plates and the snow and wind loads on the roof belong to structural design, which the National Building Code of Canada covers in Part 4, and should be checked by a qualified professional.
Common mistakes
- Using the footprint instead of the sloped area. This is the most frequent error, and it always leads to too few tiles.
- Using a generic yield instead of the value for the chosen profile and lap.
- Forgetting the waste allowance, or setting it too low for a roof with many planes.
- Mixing batches on the same roof.
- Assuming a tile with the same name from another maker will match the existing roof. Profiles from different makers can differ in size.
Codes, standards and permits
The 2020 National Building Code of Canada (NBC) is a model code, not federal law. Each province and territory adopts it, often with amendments, so the rules that apply to your roof are those of your province or territory, such as the Ontario Building Code or the Quebec Construction Code. Part 9 of the NBC covers housing and small buildings, including roof coverings.
For the tile itself, the manufacturer's data sheet is the main reference. It gives the piece dimensions, the yield and the minimum pitch, and you can ask the manufacturer whether the product has a Canadian product evaluation report. Local authorities can add requirements of their own, so confirm them with your municipal building department.
Structural changes, changes to the exterior of a building and work on heritage-designated properties usually need a municipal permit. Check before you order, because heritage rules can limit the materials you are allowed to use.
When to hire a professional
For a full roof replacement or a new build, hire an experienced roofing contractor. The tile count is a budgeting step and does not replace a roof design. A professional checks the structure (rafters, battens and plates), the underlay or sheathing, the pitch, and the flashing at the ridge, hips, valleys and eaves. On older buildings, have the structure inspected before any work starts, because hidden decay in the framing can change the whole job.
Frequently asked questions
How many roof tiles do I need for 100 m² of roof?
Multiply the sloped area by the yield from the data sheet, then by 1.10 for a 10% waste allowance. For example, with an assumed yield of 16 pieces per m² (Marseille profile): 100 × 16 × 1.10 = 1,760 tiles. Each extra piece per m² of yield adds 110 tiles on 100 m² of roof, so the figure from your product's data sheet matters. These numbers assume 100 m² of sloped roof surface, not footprint. Enter the real sloped area and the data-sheet yield into the calculator for an exact count.
How do I work out the number of barrel tiles per m²?
Barrel tile is laid as two pieces, a pan and a cover, so its yield depends on the piece dimensions and the lap. Take the figure from the manufacturer's data sheet rather than a general value. Then multiply it by the sloped area and add the waste allowance. For example, if the data sheet gives an assumed 13 pieces per m², a sloped area of 50 m² needs 650 pieces, plus 65 for a 10% allowance, for 715 in total. Check the minimum pitch in the same data sheet, because water must drain between the pan and the cover.
What is the difference between Marseille and barrel tile?
Marseille tile is a single interlocking flat piece that lays quickly and aligns mechanically, which is why it is common on new roofs. Barrel tile is made of two pieces, a pan and a cover, laid in alternating rows. It takes longer to install and gives a traditional curved look, so it is more often chosen for heritage restorations or where the design calls for it. Cost depends on the local market and the product, so get quotes per square metre installed rather than comparing piece prices.
Should I use the footprint or the sloped area of the roof?
Always the sloped area, which is the real surface of the roof. The footprint on a plan is always smaller. To convert, multiply the footprint by the square root of 1 plus the slope squared: area = footprint × √(1 + (slope/100)²). For a 30% slope the factor is 1.044, and for 45% it is 1.097. Using the footprint leads to ordering too few tiles, which can leave you short at the end of the job.
What roof pitch do I need for each tile type?
Pitch requirements depend on the profile, the manufacturer and the local climate, so check each product's data sheet for its minimum pitch. As a general rule, interlocking profiles such as Marseille can work at lower pitches than barrel tile, which needs a steeper slope so that water drains between the pan and the cover. Flat and Roman profiles also need adequate pitch and proper underlay. In areas with heavy rain or snow, a steeper pitch and good underlay help reduce the risk of leaks. Do not rely on a general figure for a specific roof without the product data.
Can I mix tiles from different batches on the same roof?
In practice, it is not recommended. Tiles of the same model from different production batches can vary slightly in size, colour or glaze, and the difference often shows after a few years of sun and rain. Buy the full count from one batch, including the waste allowance, and keep the spares for future repairs. A spare batch stored in a dry place is often the only way to match a tile years later.
When should I hire a roofing contractor?
For any full roof replacement or new build, hire an experienced roofing contractor. The tile count is a budgeting step and does not replace a roof design. A professional checks the structure (rafters, battens and plates), the underlay or sheathing, the pitch, and the flashing at the ridge, hips, valleys and eaves. On buildings older than 30 years, or on heritage-designated properties, have the structure inspected before any roof work. Permits may be needed for structural changes, so check with your municipal building department.
Related calculators
By RivoCalc · Reviewed under our editorial methodology · Updated June 3, 2026
This calculator gives an estimate of material quantities for planning and ordering. Real requirements depend on the roof geometry, the product data sheet, the applicable building code and the site. For structural, roofing or permit questions, consult a qualified professional and your municipal building department.
