Skip to main content

Home Alarm Sensors Calculator by Property Type

Estimates the door and window sensors, motion detectors and total cost of a home alarm for a studio to 4-bed flat or house in the UK.

A 2-bed flat is assigned 5 door and window contacts and 2 passive infrared (PIR) motion detectors by this calculator. A 3-bed detached house is assigned 11 contacts and 4 PIR detectors, because that layout has more entry points, a garage and more external walls. These are planning values built into the calculator, and they cover a studio up to a 4-bed property.

The starting point is the property type, not a site survey. The number of bedrooms and the type of home (flat, semi-detached house or detached house) set how many contacts and motion detectors the calculator allocates. It then adds the cost of a base kit for the chosen system level, the cost of each device installed, a fixed call-out and configuration charge and, if selected, a monthly monitoring fee.

The result gives a sensible first figure for budgeting. It does not replace a survey, because the real number of openings, the layout of ground and upper floors and the construction of the walls all change what a system needs. A ground-floor flat with a French door onto a garden needs more protection than the same layout on the fourth floor, and the calculator cannot see that difference.

Read the result as a planning estimate, not a quote. Three choices shape the total most: the number of openings, the system level and whether monitoring is needed. The sections below explain how the sensor counts are set, which system level suits which home, how monitoring changes the total cost over several years, and where the estimate stops being reliable.

The explanation below uses metric units; the calculator works in either system.

The result updates automatically.

Recommendation for this home type: 7 door/window sensors + 2 PIR detectors

Sets the reference prices for the equipment. Each price can be adjusted.

Base kit £400 · sensor £35 · PIR £50 (default; adjustable)

Call-out £180 + £35/device (default; adjustable)

£40/month — a recurring cost after installation

Estimated total cost (year 1)

£1,720
Equipment
£745
Installation
£495
Monitoring (12 months)
£480
Total for year 1
£1,720

Turn this calculation into a quote for your client

We're building a tool for professionals. Be among the first to try it.

Share

How it works

1

Select the number of bedrooms, from studio to 4-bed.

2

Choose the property type: flat, semi-detached house or detached house.

3

Select the system level: basic (DIY), professional or integrated.

Formula

C_equipment = C_kit + Ns × C_sensor + Np × C_PIR C_install = C_base + (Ns + Np) × C_install_s C_1year = C_equipment + C_install + C_monthly × 12
Ns — Number of door and window sensors the calculator assigns to the property type
Np — Number of passive infrared (PIR) motion detectors the calculator assigns to the property type
C_kit — Price of the base kit (control panel, siren and keypad) for the chosen system level
C_sensor — Unit price of a door and window sensor
C_PIR — Unit price of a passive infrared (PIR) motion detector
C_base — Base installation cost (call-out and configuration)
C_install_s — Installation cost per device (door and window sensor or PIR detector)
C_monthly — Monthly monitoring fee (24-hour alarm receiving centre)

How the calculation works

How Many Sensors Does a Home Alarm Need by Property Type?

Sizing a home alarm by property type is a practical starting point for most owners. A flat in Edinburgh has different exposure from a detached house in the Cotswolds, but the number of bedrooms and the type of home capture the main differences without needing a full survey. This calculator uses those two inputs to assign a number of door and window contacts and passive infrared (PIR) motion detectors, then adds the cost of the equipment, installation and optional monitoring.

How the Sensor Counts Are Set

The counts are planning values built into the calculator. They are not figures taken from a British standard or from an installer's specification. The logic behind them is simple: every door and window that can be reached from outside is given a door and window contact, and each main circulation space, such as a hallway, living room or garage, is given a PIR detector. Larger homes and homes with more external openings receive more devices. No source is cited for the specific numbers, so use them to produce a first budget and let a site survey set the real figures.

The calculator uses these values:

  • Studio and 1-bed flat: 3 to 4 door and window contacts and 1 PIR detector covering the living room and hallway.
  • 2-bed flat: 5 contacts and 2 PIR detectors, covering the front door, the living room windows and bedrooms with balconies.
  • 3-bed flat: 7 contacts and 2 PIR detectors, covering two window frontages, two balconies and the front door.
  • 4-bed flat: 9 contacts and 3 PIR detectors, covering all frontages and circulation areas.

For houses, the perimeter is longer. The calculator assigns a 3-bed semi-detached house 9 contacts and 3 PIR detectors, and a 3-bed detached house 11 contacts and 4 PIR detectors, to cover the entrances, the garage and the external walls.

The Three System Levels

This calculator groups home alarm systems into three levels.

Basic (DIY): Wireless systems designed for self-installation and sold as starter kits. The main control is usually a phone app, and the siren is indoors. This level suits flats in lower-risk areas, tenants who want a system they can take with them when they move, and households that want basic protection on a limited budget.

Professional: This level assumes that a qualified installer fits the system. A typical setup has a control panel with a physical keypad, an external siren and a backup communication path, such as a mobile network connection, so alarm signals can still be sent if the broadband fails. It is the level most often chosen for family homes.

Integrated: Higher-specification systems that add smart-home control, cameras and smoke and carbon monoxide detection. Installation and configuration are normally carried out by a qualified installer, because the system depends on several linked devices working together.

Monitoring: Self-Contained Alarm or Alarm Receiving Centre?

A self-contained alarm sounds the siren and sends notifications to the owner, usually through an app. No third party responds unless the owner arranges it. An alarm receiving centre (ARC) monitors signals around the clock and follows agreed procedures, which can include calling keyholders or the emergency services. The right option depends on how long the home is empty and on the level of risk where it stands.

Monitoring is a recurring cost. When you compare a monitored system with an unmonitored one, look at the total over two to three years, not only the upfront price. The calculator's annual total includes one year of monitoring when that option is selected, so switching monitoring off shows the cost of the equipment and installation alone.

Home insurance policies vary. Some set conditions on alarms, such as a minimum grade or a monitored connection, so check the policy wording before choosing a system. Confirm with the insurer, not only the installer, what the policy requires.

Standards: BS EN 50131 and Grades

The standard for intruder alarm systems is the EN 50131 series, which the UK adopts as BS EN 50131. It classifies systems into four grades, from Grade 1 to Grade 4, with rising requirements for detection, tamper protection and communication. Grade 1 is the lowest grade. Where an insurer specifies a grade, that requirement applies to the policy, so ask the installer which grade the system is designed to meet and check it against the policy wording.

Common Mistakes When Sizing a System

The most frequent mistake is protecting only the inside of the home. A PIR detector senses movement once someone is already inside. Contacts on doors and windows raise the alert earlier, so a system with PIR detectors but no contacts leaves the entry points unprotected.

The second mistake is overlooking upper-floor openings that can be reached from garages, boundary walls, trees or neighbouring roofs. Balconies and windows at height should be checked during a survey, not assumed to be safe.

The third is choosing a grade below the one the insurer requires. A system that does not meet a policy condition can cause problems when you make a claim.

The fourth is forgetting pets. Standard PIR detectors may respond to a pet moving through a room. Pet-tolerant detectors are available and are worth asking about if pets roam the house.

The fifth is forgetting maintenance. Wireless devices run on batteries that need replacing, and the system should be tested regularly.

When to Ask a Qualified Installer for a Survey

Use this calculator for a first idea of costs. Ask for a site survey when the home has several entry points, more than one storey, a garage, outbuildings or large garden areas. The installer checks the real openings, the risk points and the construction of the walls, then proposes a system designed for that home and for the insurer's conditions.

Ask for a written quote that lists each device, the labour, any cabling or wall work and the monitoring fee. Check that the installer is certified under a recognised UK scheme for intruder alarms, and confirm that certification with the body that issued it.

What This Estimate Leaves Out

The calculator counts devices and applies the installation fees set in its formula. It does not include cabling in unfinished walls, cameras, extra rooms, outbuildings, repairs to damaged door or window frames, or the cost of replacing batteries over time. Those items can change the final total, so treat the result as an indicative figure.

Frequently asked questions

How many sensors does a 3-bed flat alarm need?

For a 3-bed flat, the calculator assigns 7 door and window contacts and 2 PIR motion detectors. The contacts cover the front door, the main windows and any balconies, and the detectors cover the hallway and living room. These are planning values rather than a standard requirement. A corner flat or a flat with many windows may need more contacts, while a flat with few external openings may need fewer. Confirm the figure during a site survey.

What is the difference between a basic, professional and integrated system?

A basic system is a wireless kit fitted by the homeowner, usually controlled through a phone app with an indoor siren. A professional system is installed by a qualified installer and typically includes a control panel with a keypad, an external siren and a backup communication path, so alarm signals can still be sent if the broadband fails. An integrated system adds smart-home control, cameras and smoke and carbon monoxide detection, and is normally configured by an installer. The right choice depends on the risk, the insurer's conditions and how much of the system you want to manage yourself.

Should I include monitoring in the total cost?

The annual total includes one year of monitoring when that option is selected. Switch monitoring off to see the cost of equipment and installation alone. Monitoring is a recurring cost, so compare the total over two or three years with the upfront cost. Some home insurance policies set conditions on alarms or monitored connections, so check your policy wording and confirm the requirements with your insurer before deciding.

What does BS EN 50131 mean for a home alarm?

BS EN 50131 is the UK adoption of the European standard for intruder alarm systems. It sets four grades, from Grade 1 to Grade 4, with rising requirements for detection, tamper protection and communication. Grade 1 is the lowest grade. Where your insurer specifies a grade, that requirement applies, so ask the installer which grade the system is designed to meet and check it against your policy wording.

What is not included in the estimate?

The estimate counts devices and applies the installation fees set in its formula. It does not include cabling in unfinished walls, cameras, extra rooms, outbuildings, repairs to damaged door or window frames, or replacement batteries over time. These items can change the final total, so use the result as an indicative figure and ask an installer for a written quote that lists everything included.

When should I ask for a site survey instead of using this calculator?

Use this calculator for a first idea of costs. Ask for a site survey from a qualified installer when the property has several entry points, more than one storey, a garage, outbuildings or large garden areas. The installer checks the real openings, the risk points and the construction of the walls, then proposes a system designed for your home and your insurer's conditions. Ask for a written quote that lists each device, the labour and any monitoring fee.

Related calculators

View all Renovation & Systems calculators →

By RivoCalc · Reviewed under our editorial methodology · Updated 18 July 2026

This calculator gives an indicative estimate based on property type. The device counts are planning values built into the calculator, not requirements set by a standard. Real costs depend on the number of entry points, the layout and construction of the property, and the quotation from your installer. For a detailed quote, ask a qualified alarm installer for a site survey.