Permeable Paving Block Quantity Calculator
Calculates how many permeable paving blocks a path, driveway or patio needs for any block size, with a waste allowance and an optional material cost estimate.
A permeable paving block measuring 200 × 100 mm covers 0.02 m², so a 3 m × 8 m path (24 m²) needs 1,200 blocks before any allowance for waste. Adding an illustrative 10% allowance for cuts at the edges and corners brings the order to 1,320 blocks.
Larger blocks change the count. A 400 × 200 mm block covers 0.08 m², so the same path needs 300 blocks, or 330 with the same illustrative 10% allowance. Fewer pieces make the work quicker, but blocks that must be cut to fit a boundary are harder to trim cleanly, so the allowance for larger formats needs more care.
Permeable block paving is used where rainwater should soak into the ground rather than run off: garden paths, patios, private car parks and front gardens. The surface is laid with gaps or spacers between the blocks, or uses porous blocks, so water passes through the joints into a layer of coarse stone beneath. This reduces the surface water that reaches the drains and helps prevent localised flooding on a plot.
Before ordering, measure the area as the length multiplied by the width of the space, and choose the waste allowance from the shape of the layout. A straight run needs less allowance than a curved edge or a space around a tree, where many pieces must be cut. The calculator applies the same rounding rule for every block size: the result is always rounded up to a whole block, because a part block cannot be bought.
The result is a block count only. Sub-base stone, bedding sand and jointing material are separate quantities, and they depend on the load the surface must carry and on the ground conditions. For driveways, the block thickness and base should come from the supplier's guidance or from a qualified engineer.
The explanation below uses metric units; the calculator works in either system.
The result updates automatically.
Length × width of the area to pave with permeable block paving
Choose a standard size or enter custom dimensions
Typically 10% for regular layouts; 15% with cuts or angles
Optional. Enter the unit price to estimate the total material cost
Blocks needed
10 cm × 20 cm blocks (0.0200 m² each), waste included
- Area to pave
- 20.00 m²
- Waste allowance
- 10 %
- Area with allowance
- 22.00 m²
- Area per block
- 0.0200 m²
How it works
Formula
How the calculation works
What permeable paving is and when it is used
Permeable block paving is a surface made of precast concrete blocks laid with gaps between them, or made from a porous concrete that lets water pass through the block itself. Rainwater drains through the joints or pores into the layers beneath, instead of pooling on top and running off into the drainage system. For this reason it is widely used in gardens, footpaths, private car parks and other areas where surface water runoff is a concern.
The main advantage over solid concrete slabs is permeability. Solid slabs are impermeable and need falls and a drainage system to carry water away. Permeable paving reduces the amount of surface water leaving a plot, which lowers the risk of localised flooding, limits erosion of the surrounding soil and reduces the heat that sealed surfaces release in towns. It is often chosen for schemes where sustainable drainage is a requirement or a stated priority.
Builders' merchants and large DIY retailers stock permeable blocks in several sizes, colours and finishes. The right format depends on the area, the expected load and the appearance the owner wants.
How the calculation works
The number of blocks is found by dividing the area to be paved, with the waste allowance included, by the area of one block. The result is then rounded up to the next whole number. Rounding up is essential because a part block cannot be laid, so the order must always be a whole number of units.
The calculation follows these steps:
- Measure the length and width of the space and multiply them to get the area in square metres.
- Convert the block dimensions to metres. For example, 100 mm is 0.10 m.
- Work out the area of one block by multiplying its width by its length.
- Multiply the total area by the waste factor, 1 + d/100, where d is the waste allowance as a percentage. An allowance of 10% therefore becomes a factor of 1.10.
- Divide the area including waste by the area of one block, and round the result up.
Worked example, using an illustrative 10% allowance: a path measuring 3 m by 8 m has an area of 24 m². A 200 × 100 mm block measures 0.20 m by 0.10 m, which gives 0.02 m² per block. The adjusted area is 24 × 1.10 = 26.4 m². Dividing 26.4 by 0.02 gives exactly 1,320, so the order is 1,320 blocks. If the division had given 1,320.4, the rounding rule would require an order of 1,321 blocks.
Choosing the waste allowance
The waste allowance covers cut pieces, broken blocks and losses during handling. A straight rectangular area with no obstacles needs the smallest allowance. Areas with angles, curves or cut-outs around trees, manholes, drains or curved kerbs need a larger one, and irregular shapes or spaces with many interruptions need more again. The calculator accepts any percentage, so choose the value that matches the complexity of the layout.
Underestimating is one of the most common errors. A shortfall means a second delivery, which may come from a different production batch and show a slight difference in shade. Spare blocks are also useful for future repairs, when a block cracks or the surface settles unevenly, so it is worth ordering a few more than the minimum for the job.
Block formats and their trade-offs
Smaller blocks, such as 100 × 100 mm, suit borders and transitions between different areas. They create more cuts and take longer to lay, so they are normally reserved for small areas.
The 200 × 100 mm format is widely available and suits paths, patios and parking areas. It can be laid in several patterns, including herringbone, stretcher bond and basketweave. The pattern affects the waste allowance: herringbone produces more cut pieces than a straight stretcher bond, so the allowance should be higher.
Larger blocks, such as 400 × 200 mm, cover more ground with fewer pieces, which speeds up laying. They are heavier to handle and harder to cut neatly, so the edges of the area need more planning. Square formats such as 200 × 200 mm produce fewer visible joints per square metre, which gives a cleaner surface.
Types of permeable block
Three main types are sold:
- Blocks with spacer lugs: solid blocks with raised spacers that leave drainage gaps between them. This is the most common type.
- Hollow or cellular blocks: blocks with central cavities filled with sand, gravel or topsoil. Where the cavities are planted, they allow partial re-vegetation of the surface, which suits lawn-style areas that take light foot traffic.
- Porous concrete blocks: the concrete itself is permeable, so the joints can be narrow. These blocks generally cost more but offer higher permeability.
Block thickness should match the use. Pedestrian areas usually use thinner blocks than areas where cars park, which need thicker blocks on a stronger base. The manufacturer's datasheet gives the rated thickness, and that rating should be followed.
Base and bedding preparation
The block count solves only the material question. The finished surface depends on the preparation beneath it:
- Excavation and levelling: dig out to the depth required by the expected load and the quality of the natural ground. Soft or poorly draining ground needs deeper excavation.
- Sub-base: a layer of compacted, open-graded crushed stone. It carries the load and stores water before it soaks into the ground.
- Bedding layer: a thin layer of fine sand or fine gravel that the blocks sit on, screeded level.
- Laying: place the blocks in the chosen pattern, check levels and falls, and tap each block into position with a rubber mallet.
- Jointing: compact the surface with a plate vibrator and fill the joints with fine sand or gravel, or with a jointing material suited to permeable paving.
Concrete paving blocks sold in the UK are generally specified to BS EN 1338, which sets dimensional and strength requirements. For any area carrying vehicles, a qualified engineer should confirm the sub-base and the construction build-up.
Edge cases
A waste allowance of 0% is only sensible for a simple rectangle with no cuts and no spare blocks, and even then it leaves no margin for breakage. A zero area has no physical meaning for this calculation and should not be entered. Very small areas use the same rounding rule, but a single extra block is a larger proportion of the order, so the waste choice matters more.
Irregular shapes should be split into rectangles, each measured separately, and the areas added together before applying the allowance. Where a large fixed feature occupies part of the space, such as a shed base or a raised bed, deduct its area, then keep the waste allowance for the cuts around the remaining edges.
When not to use this calculator
This calculator counts blocks. It does not design the pavement structure, size a soakaway, or check whether the surface will carry the expected load. For driveways, heavy vehicles or any area where the design affects structural safety, the sub-base thickness and block rating should come from a qualified engineer and the product datasheet.
It is also not the right tool for materials sold by coverage rather than by block, such as resin-bound gravel or gravel mulch. For those, use the coverage figure per pack given by the supplier.
Common mistakes
Mixing units is the most frequent error. The formula works in metres, so a block dimension given in millimetres must be converted before use. Transposing the width and length does not change the result, because the block area is the same either way, but entering one dimension in centimetres and the other in metres does.
Forgetting the sub-base and bedding sand is also common. These are separate quantities, usually measured by volume in cubic metres, and they must be ordered in addition to the blocks.
Skipping the allowance for cuts around edges and features leads to shortfalls, while an allowance that is set too high leaves blocks unused. Levels and falls should be checked during laying, so that water moves towards the intended drainage point rather than pooling in low spots.
Local rules and sources
Planning rules for hard surfaces differ between England, Scotland, Wales and Northern Ireland. Local planning authorities can also attach conditions to new developments that limit the impermeable area, and some properties have restrictions that change what can be done without permission. Check with your local council before starting any significant paving work.
Concrete paving blocks should be specified to BS EN 1338, and the product datasheet should confirm the rated thickness and strength for the intended use.
Frequently asked questions
What is the difference between permeable paving and ordinary concrete slabs?
The main difference is permeability. Permeable paving is laid so that rainwater can pass through the joints, or through porous blocks, and soak into a stone base or the ground below. This avoids standing water and localised flooding. Ordinary concrete slabs are impermeable and need falls and a drainage system to carry water away. Permeable paving is generally the better choice for gardens, car parks and areas where reducing surface water runoff matters. Solid slabs remain suitable where drainage is not a concern and the surface can be laid with proper falls.
Can permeable block paving take the weight of cars?
Yes, but only with the right block thickness and a properly prepared base. Blocks for pedestrian areas are usually thinner than those for parking, where a thicker block on a stronger, compacted sub-base is needed. Check the rated thickness on the manufacturer's datasheet. For driveways, car parks and any area with heavy or frequent vehicle traffic, confirm the design with a qualified engineer, because structural requirements rise sharply with load.
How many 200 × 100 mm blocks fit in a square metre?
Each 200 × 100 mm block covers 0.02 m², so one square metre needs 50 blocks with no allowance for waste. Adding an illustrative 10% allowance raises the figure to 55 blocks per square metre. Cuts around edges, corners and obstacles usually call for a higher allowance, which the calculator applies automatically for any block size. The count is always rounded up to a whole block when you place the order.
Can permeable paving be laid over an existing concrete base?
Generally not, if the purpose is to let water soak into the ground. A solid concrete base stops infiltration, so the surface loses its drainage function. If the main goal is appearance or foot comfort, ordinary slabs bedded in mortar can be laid over concrete instead. Where drainage is the priority, the existing concrete will usually need to be removed, or a drainage route provided through the joints to a suitable outlet. A qualified builder or drainage designer can confirm the right approach for the site.
What happens to the joints of permeable paving over time?
Sand or gravel joints can wash out or erode over time, particularly where water flows quickly across the surface or where weeds take hold. Check the joints periodically and top them up with fine sand or gravel as needed, and keep drainage outlets and channels clear of debris. Joints can also be planted with low, hard-wearing species that tolerate foot traffic, as is common with cellular blocks. This reduces erosion and softens the appearance of the surface.
Are there rules about permeable paving in England?
Planning rules for hard surfaces differ between England, Scotland, Wales and Northern Ireland, and the rules depend on the property and its location. Local planning authorities can also set conditions on new developments that limit the impermeable area. Check with your local council before starting, because some properties have restrictions that change what can be done without permission.
Related calculators
View all Garden, Outdoor & Water calculators →
By RivoCalc · Reviewed under our editorial methodology · Updated 30 June 2026
This calculator gives a block count only and does not design the pavement structure. For driveways, car parks or any area carrying vehicles, the block thickness, sub-base and bedding should be specified by the product supplier or a qualified engineer.
