Access Ramp Gradient Calculator
Works out the gradient of an access ramp in percentage and degrees from the rise and the horizontal run, and gives the true length of the ramp.
A ramp that rises 300 mm over a horizontal run of 5 m has a gradient of 6%, which is about 3.4 degrees. The gradient is the rise divided by the horizontal run, multiplied by 100, and it shows whether a ramp will be usable for wheelchair users, pushchairs and people with reduced mobility before any concrete is poured.
Getting the gradient wrong early is one of the most common and expensive mistakes on small building jobs. A ramp that is too steep can block wheelchair users and buggies, make it hard to move heavy materials and become slippery when wet. A gentler ramp avoids those problems, but it needs more length, and that can decide the design at a narrow front door or a side passage where the space is limited.
This calculator works from two measurements: the height difference between the lowest and highest points of the ramp, and the horizontal distance measured on plan. It returns the gradient as a percentage, the angle in degrees and the true length of the ramp surface. For a ramp with 40 cm of rise over 5 m, the gradient is 8% and the true length is about 5.02 m.
The result matters most for access ramps in public buildings and for homes where someone uses a wheelchair or has limited mobility. In England, [Approved Document M of the Building Regulations](https://www.gov.uk/government/publications/access-to-and-use-of-buildings-approved-document-m) sets out access requirements, and BS 8300 gives more detailed design guidance. Those documents set limits that depend on the length and rise of each flight, so the figure from this calculator is a starting point and not a compliance check. Scotland and Northern Ireland have their own building standards, so check the rules that apply where the building stands.
Use the result to check the drawing, then confirm the figures with your building control officer or an architect before ordering materials.
The explanation below uses metric units; the calculator works in either system.
The result updates automatically.
Height difference between the low and high points of the ramp
Horizontal projection of the ramp — the length measured in plan
Ramp gradient
- Angle of incline
- 5.71 °
- Actual ramp length
- 10.05 m
Accessibility compliance: Outside accessibility guidelines (8–15%) — needs a technical assessment
How it works
Formula
How the calculation works
How to calculate a ramp gradient and what the UK rules say
Building a ramp without working out its gradient first is one of the most common mistakes on small projects, and one of the hardest to correct afterwards. A ramp that is too steep can stop wheelchair users and buggies getting up it, make heavy barrows and trolleys hard to push, and create a slipping hazard when wet. A ramp that is very gentle can use up so much length that it no longer fits the space.
The gradient formula
A gradient is usually expressed as a percentage. The rise (H, in metres) is divided by the horizontal distance (L, in metres) and the result is multiplied by 100. A ramp with 40 cm of rise and 5 m of horizontal distance therefore has a gradient of (0.40 ÷ 5.00) × 100 = 8%. The rise is the difference in height between the lowest and highest points of the ramp surface, so include any kerb, threshold or upstand that forms part of the route.
The angle in degrees is the arctangent of H ÷ L, converted from radians. For the same example, arctan(0.40 ÷ 5.00) × (180 ÷ π) is about 4.6 degrees.
The actual length of the ramp, which is the distance you walk or roll up the surface, is the hypotenuse of the right-angled triangle formed by the rise and the horizontal distance: the square root of (H² + L²). For the same example, the square root of (0.40² + 5.00²) is the square root of (0.16 + 25.00), which gives about 5.02 m.
Why the percentage and the angle are not interchangeable
The percentage and the angle describe the same slope, but they are different numbers. At 8% the angle is about 4.6 degrees, at 15% about 8.5 degrees and at 20% about 11.3 degrees. The gap grows as the ramp gets steeper, so a value of 10 read as degrees describes a much steeper ramp (about 17.6%) than a value of 10 read as a percentage (about 5.7 degrees). Guidance on access ramps is normally written as a percentage or as a ratio such as 1:15, where the first figure is the rise and the second is the horizontal distance. Keep to one unit when you compare your ramp with a limit.
True length and when it matters
The true length is always longer than the horizontal distance, but the difference is small on gentle ramps. For gradients below 10%, the true length is less than 0.5% longer than the horizontal distance. The difference matters more for surfacing, handrails and kerb edging, because those are bought and fixed along the slope. For a 50 cm rise over 6 m, the horizontal distance is 6.00 m and the true length is the square root of (0.25 + 36.00), which is about 6.02 m.
The horizontal distance is also the figure that decides whether the ramp fits. For a rise of 20 cm, a gradient of 8% needs a horizontal distance of at least 2.50 m (0.20 ÷ 0.08). The same rise at 6% needs 3.33 m (0.20 ÷ 0.06). That difference of 83 cm can decide whether a ramp fits a narrow entrance hall, so check the horizontal space on the plan before you choose the gradient.
Gradient limits and the guidance behind them
In England, Approved Document M of the Building Regulations covers access to and use of buildings. Volume 1 applies to dwellings and Volume 2 to buildings other than dwellings. In Wales the equivalent guidance is published separately. BS 8300 is the detailed British Standard for designing for disabled people: BS 8300-1 covers the external environment, such as paths, ramps and car parks, and BS 8300-2 covers buildings. Scotland and Northern Ireland have their own building standards with their own access provisions.
The gradient limits in these documents depend on the length and rise of each flight, so there is no single figure that applies to every ramp. Read the limits for your building type directly from the current edition, and do not rely on a figure taken from a secondary source. Because the detailed requirements are updated between editions, check the version in force on the date you submit the design.
Requirements for private houses, garages and alterations depend on whether the work is subject to the Building Regulations and on the type of work involved. Ask your building control officer whether the ramp falls under any access requirement before you fix the gradient.
Handrails, landings and widths
Handrails, landings and clear widths are set by the guidance above, and the requirements depend on the length and rise of each flight and on who will use the ramp. Check these points with your building control officer, because they are among the items most often questioned on inspection. Landings are needed at the top and bottom of a ramp, and at intervals along longer flights, so allow for them in the horizontal distance you measure.
The calculator does not check widths, landings, handrails or surface friction. It only deals with the geometry of the slope.
Choosing a surface and managing slip risk
A correctly sloped ramp can still be dangerous if the surface is slippery. Slip resistance for external surfaces is commonly specified using the R-rating scale in DIN 51130, and steeper ramps usually call for a higher rating or for embedded profiles that give wheels and feet something to grip. Exposed concrete can be given a textured finish, and closely spaced grooves across the slope improve grip on wet days.
Drainage also matters. A ramp that falls towards the building can direct water into the entrance, while a poor camber can hold water in a pool at the bottom. Check the fall across the surface as well as the gradient along it, and include a drainage channel or gully where water could collect.
Planning the space and the materials
Knowing the true length of the ramp is essential for three tasks: calculating the quantity of concrete, paving or other surfacing to order, sizing the handrails, and checking that the ramp fits the space available. The last of these is often the constraint that decides the design. In a terraced house, a shared passage or a shallow front garden, the horizontal distance may be fixed, and the only choice left is the rise you can accept or the gradient you can achieve within that length.
When space is limited, it can help to split the ramp into two shorter flights with a landing between them. Two flights take up more room in total because of the landing, but they allow a gentler gradient on each flight, so check the layout on the plan before deciding.
When to use this calculator and when not to
Use this calculator to compare design options, check a drawing, estimate surfacing quantities and decide whether a ramp will fit the available space. It is a good tool for early planning and for checking the arithmetic on a builder's quote or a drawing.
Do not use it as a substitute for a structural design. A ramp that retains soil, sits over a deep excavation or carries vehicles needs a structural design by a qualified engineer. The surface, edge protection and foundations are not covered by a gradient calculation. For public buildings, the final layout must be checked against the current regulations and any planning conditions.
Common mistakes
The most common error is to enter the sloping length of the ramp as the horizontal distance. Because the sloping length is always longer, this understates the gradient, so the ramp looks gentler on paper than it will be in use. Measure the horizontal distance on the plan, or measure the sloping length and calculate the horizontal distance from it.
The second common error is mixing units. The rise is entered in centimetres and the horizontal distance in metres, so a rise of 40 entered as 40 metres would give a gradient of 800% over a 5 m run. Check the units before you read the result.
The third error is treating the percentage as an angle. An 8% ramp is about 4.6 degrees, not 8 degrees, and the two figures should not be mixed when you compare with a limit.
The fourth error is ignoring the rise of the kerb, step or threshold at the foot of the ramp. These add to the total rise, and they can increase the gradient considerably on a short ramp.
Local practice
Building control officers and planning authorities apply the rules in their own way, and a planning condition can add requirements for public access. If the ramp connects to a public footway or highway, speak to the highway authority early, because a design that works on your own land may not meet the requirements for the public route.
In short, the gradient calculation is simple, but whether a ramp is acceptable depends on the rules that apply to the building, the space, the surface and the people who will use it. Use the calculator for the arithmetic, and use the current guidance and an experienced professional for the decision.
Frequently asked questions
What is the maximum gradient for an access ramp in the UK?
No single figure applies to every building. Approved Document M in England, the equivalent guidance in Wales and BS 8300 set limits that depend on the length and rise of each flight, so read the figures for your building type directly from the current editions. Confirm the design with your building control officer, because Scotland and Northern Ireland have their own building standards.
How do I calculate the gradient of a ramp as a percentage?
Divide the rise by the horizontal distance and multiply by 100. Both measurements must use the same unit, so convert the rise to metres if you measured it in centimetres. For example, a ramp with a 30 cm rise and a horizontal distance of 4 m has a gradient of (0.30 ÷ 4.00) × 100 = 7.5%. Measure the horizontal distance on plan, not the length of the sloping surface, because the sloping length understates the gradient.
What is the difference between a gradient as a percentage and as an angle?
A percentage and an angle describe the same slope, but they are different numbers. A gradient of 8% is about 4.6 degrees, 15% is about 8.5 degrees and 20% is about 11.3 degrees. The angle is calculated as the arctangent of the gradient divided by 100. The gap between the two grows as the ramp gets steeper, so they are not interchangeable. Guidance on access ramps is normally written as a percentage or as a ratio such as 1:15, so compare like with like.
How do I work out the true length of a ramp?
The true length is the hypotenuse of the right-angled triangle formed by the rise and the horizontal distance. Its formula is the square root of (rise squared plus horizontal distance squared). For a rise of 50 cm and a horizontal distance of 6 m, the true length is the square root of (0.25 + 36.00), which is about 6.02 m. For gradients below 10%, the true length is less than 0.5% longer than the horizontal distance, so the difference is small on gentle ramps but matters when ordering surfacing and handrails.
What gradient is suitable for a domestic driveway or basement ramp?
For a private driveway or basement ramp, the practical limit is usually set by the vehicle rather than by access guidance. Ground clearance and the approach and departure angles of the car determine whether it can drive up or down the ramp without grounding, and the surface, drainage and ice risk also matter. Check the approach angle in your vehicle handbook before fixing the gradient, ask your building control officer whether any access requirement applies, and use a gentler slope where the ramp will be used in wet or icy conditions.
View all Measurements & Quantities calculators →
By RivoCalc · Reviewed under our editorial methodology · Updated 1 July 2026
This calculator gives a geometric estimate from the measurements you enter. It does not check compliance with the Building Regulations, BS 8300 or local planning conditions, and it does not design structures, handrails or foundations. Confirm the design with a qualified professional and your building control body before construction starts.
