Brick Quantity Calculator for Walls
Works out the number of bricks or concrete blocks a wall needs, with mortar joint thickness and a waste allowance included.
A brick garden wall 4.0 m long and 2.4 m high, built from 230 × 76 mm clay bricks with a 10 mm mortar joint and a 5% waste allowance, needs 489 bricks. That works out to about 50.9 bricks per square metre of wall, or 48.4 per square metre before waste is added.
The calculator works out how much wall face each brick covers, including the mortar joints around it. It divides the wall area by that effective area, adds the waste allowance and rounds up to a whole number. Enter the wall length and height in metres, the brick length and height, the joint thickness and the waste percentage, and the total updates. Because the joints are part of each brick's effective area, the result is more accurate than dividing the wall area by the brick's face size alone.
In New Zealand, brick is most often used as a veneer on timber-framed houses, and concrete block is common for garden walls, fences and some retaining walls. The same counting method applies to both, so the calculator works for clay brick and for concrete masonry units of a known face size. Check the actual dimensions on the manufacturer's data sheet, because brick sizes vary between suppliers and a few millimetres per unit adds up across a wall.
The calculator suits simple, non-structural masonry: a brick garden wall, a screen wall, an infill panel or a brick veneer face. Load-bearing, retaining and other structural walls need design by a Chartered Professional Engineer, and some masonry work may require building consent under the [Building Act 2004](https://www.legislation.govt.nz). The number of bricks is only one part of the job, so use it to plan the order alongside the mortar and wall ties.
The result updates automatically.
Typical ceiling height: 2.5–2.7 m (flat); up to 3.0 m (house) (about 8.2–8.9 ft; 9.8 ft).
Standard hollow brick: 30 cm · Acoustic brick: 37 cm (about 11.8 and 14.6 in)
Standard hollow brick: 20 cm · Thermal brick: 19 cm (about 7.9 and 7.5 in)
Typical on-site value: 1 cm (about 3/8 in)
Plain wall: 5% · With cut-outs and openings: 10%
Bricks needed
for a wall of 13.5
- Wall area
- 13.50 m²
- Bricks per unit area
- 15.4 unid./m²
- Effective area per brick
- 651 cm²
How it works
Formula
How the calculation works
How many bricks does a wall need?
Working out how many bricks a wall needs is simple arithmetic, but the answer depends on one detail that many quick estimates leave out: the mortar joint. Each brick sits on a bed of mortar and has a vertical joint at its end, so the area a brick covers on the wall is larger than the brick face alone. Leave the joints out and the count comes out too high, which means ordering pallets of spare bricks that take up space and may not match later batches.
The calculator is built for simple walls: a garden wall, a screen wall, an infill panel or the brick face of a veneer wall. It works for clay brick and concrete masonry units alike, provided you know the face size.
The formula and what goes into it
The calculator uses N = ⌈(A × (1 + D/100)) / ((L + J) × (H + J))⌉. The steps behind it are:
- Work out the wall area A in square metres by multiplying length by height. A wall 4.0 m long and 2.4 m high has an area of 9.6 m².
- Work out the effective area of one brick. A brick with a 230 mm length and 76 mm height, with a 10 mm joint added to each dimension, covers 0.240 m × 0.086 m = 0.02064 m² of wall. The joint is added to both length and height, because the vertical joint sits at the end of the brick and the bed joint sits beneath it.
- Divide the wall area by the effective brick area: 9.6 ÷ 0.02064 = 465.1 bricks with no waste.
- Multiply by 1 plus the waste percentage. With 5% waste, that gives 488.4 bricks.
- Round up to the next whole brick, which gives 489.
The rounding up matters. A fraction of a brick cannot be ordered, and rounding down always leaves you short at the end of a course.
The joint thickness is the value that is easiest to get wrong. The joint is set by the design and the mortar specification, not by the brick itself. This calculator starts from 10 mm as a planning value, so check it against the project drawings or your builder's specification before ordering. The unit specification EN 771-1 covers the units, not the joint. A thinner joint means each brick covers less area and the count rises; a thicker joint does the reverse.
Common brick sizes and why the face matters
The formula depends only on the length and height of the brick face that shows on the wall, plus the joint. The thickness of the wall, meaning the depth of the unit through the wall, does not change how many units you need per square metre of face. Thickness changes the width of the finished wall, the wall ties and cavity requirements, and the price per unit, but not the count for a single leaf of brick.
Clay brick veneer is commonly built as a single leaf of modular brick. A modular brick has a face of about 230 × 76 mm, though exact dimensions vary between manufacturers. Concrete masonry blocks have larger faces, so fewer units are needed per square metre. Measure a sample or check the data sheet before entering dimensions, because a difference of 2 mm in height across 40 courses adds up to 80 mm of wall.
Choosing the waste allowance
Waste covers cuts at the corners, reveals around windows and doors, cuts in the top course, and units broken during handling. The calculator offers 5% for a simple rectangular wall with few openings, and 10% for a wall with several windows, electrical boxes, or junctions with columns or other walls. If you are cutting bricks with an angle grinder, each cut can waste a unit, so the higher allowance is the safer choice.
Ordering a little extra also covers variation between production batches in size and colour. Keep a small reserve for repairs, because matching a later batch exactly is difficult.
Common mistakes
Ignoring the joint is the most frequent error. It makes the count too high, which is inexpensive to correct before ordering but wasteful if full pallets are bought and left unused. Using the brick face alone, such as 230 × 76 mm without the joint, is the same mistake.
Forgetting waste is the opposite error. Walls rarely match whole brick dimensions, so there are always cut units at the ends, around openings and at the top. A wall with a window and a door needs the openings subtracted from the gross area, and then the waste allowance added to what remains.
Unit mistakes are also common. The calculator works in metres, so a wall measured as 4000 mm must be entered as 4.0 m. Entering a length in millimetres instead of metres makes the area 1000 times too large, and entering both dimensions in millimetres makes it a million times too large, so check the wall area in square metres before you order.
Walls that need an engineer
Most of New Zealand lies in a seismically active region, so any masonry that carries load, retains soil or forms part of the building's bracing needs engineering design. The calculator does not size those walls. Their design follows the New Zealand Building Code, which is made under the Building Act 2004, and it is usually undertaken by a Chartered Professional Engineer. Brick veneer over timber framing, for example, depends on the ties and the framing design, not on the brick count. The number of bricks is the last item to settle, after the structure has been designed.
For a boundary wall or a retaining wall, check with your local council whether building consent is needed. Councils set their own requirements for height and foundations, and these can change the amount of material as well as the count.
Summary for planning
Work out the wall area, the effective brick area and the waste allowance, then round up. Check the brick face on the data sheet, confirm the joint with the drawings or your builder, and keep a small reserve for repairs.
Frequently asked questions
How many bricks do I need per square metre of wall?
For a modular clay brick with a 230 × 76 mm face and a 10 mm mortar joint, a square metre of wall takes about 48.4 bricks before waste. With a 5% waste allowance, plan for about 50.9 bricks per square metre, or round up to 51 for a simple wall. Walls with several openings or many cut junctions are better served by the 10% allowance, which brings the figure to about 53.3 bricks per square metre.
What size brick is used for brick veneer in New Zealand?
A modular clay brick with a face of about 230 × 76 mm is a common reference size, but exact dimensions vary between manufacturers. Check the data sheet for the product you are buying and enter its real length and height in the calculator. Concrete masonry blocks have larger faces and need fewer units per square metre, so do not use the brick figures for block work.
Does the wall thickness change the number of bricks?
For a single leaf of brick, no. The count per square metre depends only on the length and height of the brick face and the joint thickness. A 110 mm thick wall and a 230 mm thick wall with the same face size need the same number of units for each square metre of face. Thickness changes the width of the wall, the wall ties and the material cost. A double-leaf wall needs a separate count for each leaf.
What waste allowance should I use for bricks?
Use 5% for a simple rectangular wall with few openings. Use 10% for a wall with windows, doors, electrical boxes or junctions with columns and other walls. If you cut bricks with an angle grinder, or the wall has irregular edges, the higher allowance is the safer choice. Keep a small reserve beyond the calculated figure as well, because batches vary in size and colour, and spare bricks help with repairs later.
What is the correct mortar joint thickness?
The joint thickness is set by the design and the mortar specification, not by the brick itself, so use the value on the project drawings or the one your builder works to. This calculator starts from 10 mm as a planning value, and you can change it in the field above. Thinner joints need more precise bricklaying. Thicker joints use more mortar and reduce the number of bricks per square metre.
When do I need an engineer for a brick wall?
You need a Chartered Professional Engineer for any wall that carries load, retains soil or forms part of the building's bracing. Most of New Zealand lies in a seismically active region, so masonry design is a structural matter, not just a quantity question. Check with your local council whether building consent is needed for the wall. The calculator is suitable for a non-structural garden wall, screen wall or brick veneer face, and for ordering the material for those.
View all Measurements & Quantities calculators →
By RivoCalc · Reviewed under our editorial methodology · Updated 4 June 2026
This calculator gives an estimate of the number of bricks for simple, non-structural masonry walls. It does not design structural, load-bearing or retaining walls, which need a Chartered Professional Engineer. Actual quantities vary with brick size tolerance, joint practice, openings, cutting and breakage, so order with a reserve and check the requirements for your site with your local council.
