Skip to main content

Tile Quantity Calculator for Walls and Floors

Calculates how many tiles you need for a wall or floor, including a waste allowance for straight or diagonal layouts.

A wall measuring 2.5 m by 2 m, tiled with 30 × 60 cm tiles and a 10% waste allowance for a straight lay, needs 31 tiles. Switch to 20 × 20 cm mosaic tiles across the same wall and the count rises to 138, which is 4.5 times as many tiles for exactly the same area.

The number of tiles per square metre is the inverse of the area of one tile. A 30 × 60 cm tile covers 0.18 m², so you need about 5.6 tiles per m². A 20 × 20 cm mosaic covers 0.04 m², which works out at 25 tiles per m². The waste allowance depends on how the tiles are laid. A straight lay, with joints parallel to the walls, is normally planned with 10% extra. A 45-degree diagonal lay creates more cut edges, so 15% is a more realistic starting point. Patterns such as herringbone need 20% or more. Large formats of 60 × 120 cm or bigger keep the same percentage, but a single broken cut wastes a large piece of material, so a little spare is worth having.

Enter the length and width of the area, the width and height of the tile, and the waste allowance for your layout. The calculator returns the exact number of tiles, rounded up. Rounding up matters: a result of 33.3 tiles means you order 34, never 33. Because tiles are sold by the box, check the final number against the pieces per box printed on the packaging before you buy.

Typical uses include a bathroom in a weatherboard house in Auckland, a kitchen splashback in a townhouse in Wellington, or a floor in a rebuild in Christchurch. A bathroom floor of 2 m by 3 m (6 m²) tiled with 30 × 60 cm tiles needs 34 tiles before any allowance, and 37 with a 10% straight-lay allowance. Buy a few spares for future repairs, because a replacement tile from a different batch can differ in shade.

To estimate the material cost, enter your own price per square metre. The calculator holds no price data, so the cost is only as accurate as the figure you type in.

The result updates automatically.

Common sizes: 20, 30, 45, 60, 120 cm (about 8, 12, 18, 24, 47 in)

Common sizes: 20, 30, 60, 120 cm (about 8, 12, 24, 47 in)

Straight lay: 10% · Diagonal (45°): 15% · Complex patterns: 20%

Reference value for this type of tile. Adjust to match the quote you've received.

Tiles needed

37pieces

for 6.00 of area

Area to cover
6.00 m²
Area with waste included
6.60 m²
Area per piece
1,800 cm² (0.1800 m²)

Turn this calculation into a quote for your client

We're building a tool for professionals. Be among the first to try it.

Share

How it works

1

Measure the length and width of the area to be tiled, in metres.

2

Enter the width and height of the tile you have chosen, in centimetres.

3

Set the waste allowance: 10% for a straight lay, 15% for a diagonal lay.

Formula

N = ⌈(C × L × (1 + D/100)) / (wT × hT)⌉
N — Number of tiles needed (rounded up)
C — Length of the area to be tiled (m)
L — Width of the area to be tiled (m)
D — Waste allowance (%)
wT — Tile width (m) = width in cm ÷ 100
hT — Tile height (m) = height in cm ÷ 100

How the calculation works

How to work out how many tiles you need

Tiling is one of those jobs where the sums are easy and the result is still often wrong. The area is simple to calculate, but the number of tiles you actually need depends on how many of them end up cut, broken or left over at the edges. Buying exactly the area you measured almost always leaves you short. Tiles from a single batch are not always available later, and a replacement from a different production run can show a visible difference in shade, so getting the first order right matters more than it might seem.

The formula and what it leaves out

The calculator uses N = ⌈(C × L × (1 + D/100)) / (wT × hT)⌉. The area of the surface, C × L, is multiplied by one plus the waste allowance, which adds the extra tiles needed for cuts and breakage. That result is divided by the area of one tile, wT × hT, where the tile dimensions are converted from centimetres to metres. The answer is then rounded up to a whole tile.

For a wall of 2.5 m by 2 m, the area is 5 m². With a 10% allowance that becomes 5.5 m². A 30 × 60 cm tile is 0.3 m by 0.6 m, or 0.18 m², so 5.5 ÷ 0.18 = 30.6, which rounds up to 31 tiles.

The formula is deliberately simple. It does not model the layout itself, so it does not know whether a wall has a window, a niche or a pipe running through it. The waste allowance stands in for all of that, which is why the choice of allowance matters: it has to cover the cuts that the particular room will need.

Tile sizes and tiles per square metre

Tiles per square metre is the inverse of the area of one tile. Common sizes work out as follows:

  • 20 × 20 cm: 0.04 m² per tile, or 25 tiles per m². The classic size for small walls and bathroom mosaics.
  • 30 × 60 cm: 0.18 m² per tile, or about 5.6 tiles per m². A medium format that balances the number of cuts against the look of the finished wall.
  • 60 × 60 cm: 0.36 m² per tile, or about 2.8 tiles per m². A popular floor size, especially in open-plan kitchens.
  • 60 × 120 cm: 0.72 m² per tile, or about 1.4 tiles per m². A large format with fewer grout lines.

Large formats have an obvious advantage: fewer joints mean less grout and less cleaning, which is a real benefit in bathrooms and kitchens. They also demand more from the surface beneath. A small dip or ridge in a substrate shows up far more clearly on a large tile than on a small one. Check the flatness requirements in the tile manufacturer's technical data sheet, and check the substrate before you lay anything.

Waste allowance by layout

The waste allowance is the calculator's most important input. It is a judgement about the layout rather than a fixed property of the tile. The starting points that most tilers work from are:

  • Straight lay, with joints parallel to the walls: 10%.
  • Diagonal lay at 45 degrees: 15%.
  • Complex patterns such as herringbone or mixed mosaic: 20% or more.

These are common starting points, not values set by a standard. EN 14411:2016, the European standard for ceramic tiles, covers definitions, classification, characteristics and marking. It does not set a waste allowance. That decision belongs to the person doing the job, based on the room and the pattern.

Even for a straight lay, a bathroom with many cut-outs for waste pipes, shower valves and the edges of a vanity needs the full 10% allowance. A room with a lot of cut-outs or an irregular shape can use up the allowance faster than expected.

Measuring the area correctly

Measure wall to wall and floor to ceiling, or the full length and width of the floor. Small windows, door openings and niches are usually not deducted, because the cuts around them use up material that would otherwise be spare. As a rule of thumb, only large openings are worth subtracting, such as a wide garage door wider than about 1.5 m.

In a bathroom, the areas people most often forget are the wall behind the toilet, the wall above a wall-hung vanity, and the strip up to a suspended ceiling if the tiles run that high. Measure each surface separately if the heights differ, for example where the tiling stops at a window sill.

Common mistakes

Buying the exact area with no allowance. This is the most common error and the most expensive to fix. A tile line may be discontinued, a batch may change, and the shop may not have stock when you need it. Two or three square metres of spare tile cost little compared with an unfinished wall.

Switching to a diagonal layout without changing the allowance. Diagonal tiling creates far more cuts along the edges, so the 10% that worked for a straight lay is usually not enough. Change the allowance to 15% whenever the layout changes.

Ignoring batch variation. Tiles from different production runs can vary in shade, and the difference is easy to see once the wall is finished. Buy the whole job from one batch, check the batch code on the box, and keep a few spare tiles from the same batch.

Choosing between ceramic and porcelain

The calculator works the same way for both, but the material affects the choice. Glazed ceramic wall tile has a higher water absorption and is generally used on interior walls. Porcelain stoneware has a water absorption of 0.5% or less, which EN 14411:2016 places in group BIa. That low absorption makes porcelain suitable for floors, wet areas and heavy foot traffic, and for external use where the data sheet confirms it. If you are tiling outdoors in a colder area such as Queenstown, check the data sheet for frost resistance, which is tested under the same standard.

Materials beyond the tiles

This calculator counts tiles only. The rest of the job needs tile adhesive, grout, spacers, a primer for the substrate and a sealant at changes of plane, such as where the wall meets the bath. In a wet area, the waterproofing membrane or board system matters as much as the tile itself. In New Zealand, wet areas such as bathrooms and laundries are covered by clause E3 (Internal Moisture) of the New Zealand Building Code, which sets the performance requirements for keeping moisture out of the building structure. Check with your local council whether a building consent is needed if the work changes the structure or the plumbing.

When to ask a professional

For a standard rectangular wall or floor, the calculator gives a reliable figure. For a herringbone pattern, two tile formats in one room, a diagonal layout with many cuts, or irregular shapes such as columns, curved niches or benchtops with angled edges, speak to a qualified tiler (a tradie) before you buy. An experienced tiler can plan the cuts to reduce waste, which matters most with expensive tiles, where every piece has a real effect on the budget.

Using the price field

Enter your price per square metre to estimate what the tile costs. Only the figure you type in is used. Compare the total with the quote from your tiler or supplier, because delivery, cutting tools, adhesive and grout are not included in the estimate.

Frequently asked questions

How many tiles do I need for a bathroom?

It depends on the size of the room. A small bathroom with a floor of 1.5 m × 2.5 m (3.75 m²) and about 12 m² of wall tiling needs around 97 tiles of 30 × 60 cm with a 10% allowance. Calculate the floor and the walls separately and add the results, because each surface has its own cuts. Use your own measurements in the calculator for a reliable figure, and measure any shower or bath surround as its own area if its height differs from the rest of the wall.

What waste allowance should I use for tiles?

Use 10% for a straight lay, with joints parallel to the walls, 15% for a diagonal lay at 45 degrees, and 20% or more for complex patterns such as herringbone. These are common starting points, not values set by a standard. In a bathroom with many cut-outs, such as waste pipes, shower valves and the edges of a vanity, keep the 10% allowance even for a straight lay, because breakage during fitting is common. If you are unsure, ask a tiler.

Do I deduct doors and windows from the tiling area?

In small bathrooms and kitchens, usually not. The cuts around a window, a door frame or a niche use up enough tile to make up for the area that is not tiled. Consider subtracting only large openings, such as a wide garage door wider than about 1.5 m. For small windows and niches, include their area in the calculation so the result stays on the safe side.

What is the difference between ceramic and porcelain tile?

Glazed ceramic tile has a higher water absorption and is usually used on interior walls. Porcelain stoneware has a water absorption of 0.5% or less, which places it in group BIa under EN 14411:2016. Its low absorption makes it suitable for floors, wet areas and heavy foot traffic, and for external use where the manufacturer's data sheet confirms it. Both types are covered by the same European standard, so compare the group and the data sheet rather than the name on the box.

How many boxes of tiles should I buy?

Divide the total number of tiles from the calculator by the number of tiles per box, which is printed on the packaging. Add any spares you want to keep for future repairs, then round up to the next whole box, never down. The number per box varies with the tile size, so check the label on each product rather than relying on a general figure.

When should I ask a professional tiler to measure up?

For a simple rectangular wall or floor, the calculator is enough. Speak to a tiler before you buy if you plan to combine two tile formats, use a herringbone or other complex pattern, lay diagonally in a room with many cuts, or tile around irregular shapes such as columns, curved niches or benchtops with angled edges. An experienced tiler can plan the cuts to reduce waste, which matters most with expensive tiles.

View all Measurements & Quantities calculators →

By RivoCalc · Reviewed under our editorial methodology · Updated 3 June 2026

This calculator is for information purposes only. Results are estimates based on standard formulas and may vary depending on real-world conditions. Consult a professional before making important decisions.