Brick Quantity Calculator for Walls
Calculates how many bricks a wall needs, including the mortar joint and a waste allowance. Optional material cost estimate.
A wall measuring 4 m × 2.5 m, built with bricks of 300 × 200 mm, a 10 mm mortar joint and a 10% waste allowance, needs 169 bricks. Before waste, that is about 15.4 bricks per square metre of wall. If the joint is left out of the calculation, the same wall appears to need 184 bricks, about 9% more than the correct figure, so the error leads to over-buying rather than running short.
The number of bricks per square metre depends only on the visible face of the brick and the joint thickness. Brick depth changes how wide the finished wall is, but not how many bricks cover a given area. Enter the wall length and height, the brick length and height, the joint thickness and the waste allowance, and the calculator returns the total, rounded up to the next whole brick.
The calculator suits simple masonry: an internal partition, a garden wall, or infill around an existing opening, built in clay bricks or concrete blocks of a known face size. It is a quantity tool for planning materials. It does not check whether a wall can carry load, and it does not replace the design of a qualified structural engineer, which matters for any wall that holds weight or is being removed.
In a renovation, a new brick partition often follows the removal or relocation of an old wall. Before any hacking starts, check with the Building and Construction Authority (BCA) whether the work needs approval, because requirements depend on the type of property, whether an HDB flat, a condominium or a landed house. Condominium owners should also check the rules of their management corporation. The quantity calculated here is only useful once the wall itself is confirmed as buildable.
The result updates automatically.
Typical ceiling height: 2.5–2.7 m (flat); up to 3.0 m (house) (about 8.2–8.9 ft; 9.8 ft).
Standard hollow brick: 30 cm · Acoustic brick: 37 cm (about 11.8 and 14.6 in)
Standard hollow brick: 20 cm · Thermal brick: 19 cm (about 7.9 and 7.5 in)
Typical on-site value: 1 cm (about 3/8 in)
Plain wall: 5% · With cut-outs and openings: 10%
Bricks needed
for a wall of 13.5
- Wall area
- 13.50 m²
- Bricks per unit area
- 15.4 unid./m²
- Effective area per brick
- 651 cm²
How it works
Formula
How the calculation works
How many bricks does a wall need?
Working out how many bricks a wall needs looks simple, but two details are easy to get wrong: the mortar joint between bricks and the waste allowance. This calculator divides the wall area by the effective area of one brick, adds a waste allowance and rounds up to the next whole brick. The result is a planning quantity, ready to check with your builder or supplier before ordering.
It is most useful for internal partitions, garden walls and infill around an existing opening. Each of these jobs starts with a rectangle of known size, which is exactly what the calculator needs. Walls with several openings take more work, as explained below.
The formula and what goes into it
The expression is N = ⌈(A × (1 + D/100)) / ((L + J) × (H + J))⌉. A is the wall area in square metres, found by multiplying length by height. D is the waste allowance as a percentage. L and H are the length and height of the brick face, and J is the mortar joint thickness. The brackets around the whole expression mean the result is always rounded up, so the answer is a whole number of bricks.
Take a wall of 4 m by 2.5 m, which gives an area of 10 m². A brick with a 0.30 m face length and a 0.20 m face height, laid with a 0.01 m joint, occupies 0.31 × 0.21 = 0.0651 m² once the joint is included. Before any waste, 10 m² divided by 0.0651 m² is about 153.6 bricks. Adding a 10% allowance raises the wall area to 11 m², and 11 m² divided by 0.0651 m² is about 168.97, which rounds up to 169 bricks.
This works out to about 15.4 bricks per square metre before waste, and about 16.1 per square metre with a 5% allowance.
Why the joint matters
Each brick takes up more than its face, because the mortar joint sits along its bed and its end. If the joint is ignored, each brick is assumed to cover only 0.30 × 0.20 = 0.06 m². That figure is about 8% smaller than the real area of 0.0651 m² per brick, so the count comes out higher. For the same 4 m × 2.5 m wall with the same 10% waste, the calculation gives 184 bricks instead of 169, which is roughly 9% more than needed.
The consequence is over-ordering, not shortage. Surplus bricks tie up money and take up space on site, and some bricks break or get damaged. A practical risk comes from using a joint thickness that does not match the one the wall is laid to, because the difference adds up across hundreds of bricks.
The joint thickness is a design and workmanship decision. The 10 mm joint used in these examples is a common planning value, but it is not a universal rule. Thicker joints use more mortar and reduce the number of bricks needed, while thinner joints need more careful laying. Confirm the joint size against the wall design and the mortar specification for your project.
Brick depth does not change the count
Bricks are made in several depths, and the depth sets the finished width of the wall, not the number needed to cover an area. A brick with a 300 × 200 mm face needs the same count per square metre whether it is 100 mm, 150 mm or 220 mm deep. The calculator uses the face only, so enter the length and height of the visible face and choose the depth separately when you plan the wall thickness, weight, insulation and any acoustic or fire requirement.
Depth does affect weight and cost per unit, which you can enter in the unit price field once you have a quote. If a wall is built as two leaves, such as a cavity wall with a different brick on each side, calculate each leaf separately. Each leaf has its own face size, so its count may differ from the other, even when both leaves cover the same wall area.
Choosing the brick and checking its face size
Bricks differ in how they are made and how they behave. Solid bricks are heavy and strong, which suits garden walls and heavier-duty work. Hollow or perforated bricks are lighter and suit internal partitions, where weight and ease of handling matter. Concrete blocks are another option for partitions and infill. The choice affects weight, thermal and acoustic behaviour, and cost, and it should follow the design rather than the calculator.
Face size is the most important input, and it should come from the manufacturer's data sheet or the supplier's product specification. Do not reuse a size from an older project without checking, because products change and a wrong face size shifts the whole result. Measure a sample brick if one is available, and convert millimetres to metres before entering, so 300 mm becomes 0.30 m.
Setting the waste allowance
The waste allowance covers cuts at the corners, around door and window openings, around electrical boxes, at junctions with columns, and bricks broken in transport or handling. A simple rectangular wall with few openings needs less allowance than a wall with many cuts. The calculator's suggested inputs are 5% for simple walls and 10% for walls with many cuts. These are planning choices, not figures taken from a standard.
Waste is hard to predict until the work starts. Keep a spare set of bricks on site for repairs, because batches can vary slightly in size and colour from one delivery to the next. Storing bricks on pallets, off the ground and covered, keeps them clean and dry until they are laid.
Walls with openings
The calculator works on a rectangle. For a wall with a window or door, there are two simple options. You can calculate the full wall and rely on the waste allowance to cover the openings, which tends to over-order slightly. Or you can calculate the brick count per square metre and multiply it by the net area of wall you actually need to build. Either method is acceptable for planning; state which one you used so the quantity can be checked later.
When not to use this calculator
The calculator gives a quantity, not a structural check. Load-bearing walls, retaining walls, walls that carry heavy loads from above, and walls that are being removed or altered need a qualified structural engineer. Masonry design is covered by Eurocode 6 (EN 1996), which the engineer applies with the Singapore national annex.
Renovation work calls for the same care. In an HDB flat, a condominium or a landed house, check with the Building and Construction Authority (BCA) whether approval is needed before any hacking begins. Condominium owners should also check the rules of their management corporation. Fire-rated and acoustic partitions have their own specifications, which this calculator does not cover.
Common mistakes
Four mistakes come up again and again. The first is leaving out the joint, which in this example overstates the count by about 9%. The second is skipping the waste allowance, which leaves the job short when cuts are made. The third is buying exactly the calculated number with no spare, which causes problems if a batch changes or a brick is damaged. The fourth is mixing units: entering millimetres into a field that expects metres gives a result a thousand times too large.
A fifth mistake is using the brick depth where the face length is needed. The calculator uses the face of the brick, so the depth has no effect on the count. Confusing the two inputs produces a wrong result that still looks plausible, which is why it is worth checking the entered values against the data sheet.
Using the result for the rest of the job
The brick count is one part of the material and labour picture. Once you have it, mortar, plaster and labour can be estimated separately, each with its own inputs. Keep the figure and its assumptions together, including the joint, the face size and the waste allowance, so the estimate can be checked later. A written record of the assumptions also helps when a second delivery is needed.
Summary
To work out the number of bricks for a wall, measure the wall in metres, take the face size from the manufacturer's data sheet, use a realistic joint thickness and choose a waste allowance that matches the complexity of the wall. The calculator returns a whole number of bricks, rounded up. Check the result against the design, keep a spare set, and confirm any structural or approval requirements before the work starts.
Frequently asked questions
How many bricks do I need per square metre of wall?
With bricks of 300 × 200 mm and a 10 mm joint, each brick covers 0.0651 m² of wall, which gives about 15.4 bricks per square metre before waste. With a 5% waste allowance the figure rises to about 16.1 bricks per square metre. Brick depth does not change this count, only the finished width of the wall. For the total for a specific wall, use the calculator, which rounds up to the next whole brick.
Does the mortar joint really change the number of bricks?
Yes. The joint adds to both the length and the height of each brick, so one brick covers 0.0651 m² with a 10 mm joint, instead of 0.06 m² on the face alone. Ignoring the joint overstates the count by about 9%. For a 4 m × 2.5 m wall with 10% waste, the calculation gives 169 bricks with the joint and 184 without it. Ignoring the joint therefore leads to over-buying.
What waste allowance should I use for bricks?
A lower allowance suits a simple rectangular wall with few openings. A higher allowance suits walls with several window and door openings, electrical boxes, junctions with columns or bricks cut on site. The calculator's suggested inputs are 5% for simple walls and 10% for walls with many cuts. These are planning choices rather than standard figures, so check with your builder if the wall is complex.
Where do I find the brick size to enter?
Use the face length and height on the manufacturer's data sheet or the supplier's product specification. Enter the visible face, not the depth, because the depth only changes the wall thickness. Measure a sample brick if you have one, and convert millimetres to metres before entering, so 300 mm becomes 0.30 m. Do not reuse a size from an older project without checking the product.
Is a 10 mm mortar joint the right thickness?
A 10 mm joint is a common planning value, and it is the default used in the examples here. The right thickness depends on the wall design, the mortar specification and the workmanship on site. The European standard EN 771-1 covers the bricks themselves rather than the joint, so the joint should be set by the design. Thicker joints use more mortar, and thinner joints need more careful laying.
When do I need a professional for a brick wall?
Involve a qualified professional for any load-bearing or structural wall, for any wall removal or alteration, and for any work that may need approval. Confirm with the Building and Construction Authority (BCA) whether approval is needed before any hacking begins, in an HDB flat, a condominium or a landed house. This calculator suits simple partitions and garden walls. It gives a quantity only and does not replace a structural assessment, so the engineer's design should set the wall's dimensions and specification.
Related calculators
Sand and Cement Calculator for Mortar
Calculates the number of cement bags and the sand volume for mortar, based on the area, layer thickness and mix ratio.
Cement Bags Needed for Concrete Calculator
Calculates the cement bags needed for concrete from its volume, cement content and bag weight, with a 5% allowance for site losses.
View all Measurements & Quantities calculators →
By RivoCalc · Reviewed under our editorial methodology · Updated 4 June 2026
This calculator gives an estimate of the number of bricks for planning purposes only. Actual quantities vary with the product, site conditions, workmanship and design. It does not replace the work of a qualified structural engineer. Any wall that carries load, or any alteration to an existing wall, should follow the engineer's design and any approval required by the relevant authority.
