Full Painting Cost Calculator for Singapore Homes
Estimates the total cost of painting walls and ceilings, splitting materials from labour and applying a labour multiplier for your location.
Take a 4-room HDB flat with about 120 m² of wall surface and 90 m² of ceiling. That is 210 m² of surface per coat, so two coats need about 420 m² of coverage, or roughly 42 litres of paint at an assumed coverage of 10 m² per litre, before any primer or consumables are added. The calculator works out the total cost from these areas and the rates you enter.
Those areas are the inputs that matter most, but the total cost has two separate parts. Materials cover the paint, primer, filler, painter's tape, rollers, drop sheets and sandpaper. Labour covers the time a painter spends preparing, painting and cleaning up. Labour is the part that depends most on the contractor and the job, so the calculator keeps the two rates apart and applies a labour multiplier to the labour side only.
The same method works for a condominium in Bukit Timah, a landed house in Bishan or a BTO flat in Punggol. Only the areas and conditions change. Ceilings take longer per square metre than walls because the work is done with the arms raised, so the calculator gives them their own labour rate. Measure the areas from your floor plan, deduct large openings if you want a tighter figure, and enter 0 for the ceiling area if you are not painting the ceilings.
Treat the result as a planning estimate, not a quote. The condition of the surfaces, access, working hours and the finish you choose all change the final figure, and a contractor needs to see the walls before pricing. Hacking, wet works and structural changes can also need approval before work starts. In an HDB flat, the approval comes from HDB, and in a condominium the management corporation sets its own rules on working hours and lift use.
If you see damp patches, mould, bubbling or large areas of peeling paint, find and fix the cause before painting. Paint applied over moisture hides the problem only for a while, and the new finish will fail. The estimate assumes sound surfaces, so a clear diagnosis first makes the figure far more reliable.
The result updates automatically.
Total of all the walls. Enter 0 if you're not painting walls.
The same as the floor area of the rooms. Enter 0 if you're not painting ceilings.
Singapore reference values for material and labour per square metre of wall and ceiling, shown before any adjustment for location, access or finish. Adjust the inputs to match the itemised quotes you receive, and check whether each quote includes GST.
Estimated total cost
90 painted
- Materials — walls
- $420
- Materials — ceilings
- $218
- Labour — walls
- $270
- Labour — ceilings
- $188
- Total area painted
- 90 m²
How it works
Formula
How the calculation works
How to estimate the cost of a full repaint in Singapore
A full repaint is one of the most common home maintenance jobs, and one of the most often underestimated. Most owners buy the paint, get a quote for labour and then find the final figure is higher than expected, because the cost has two parts that behave differently. This calculator separates them: materials for the walls and ceilings on one side, and labour on the other, with a multiplier that adjusts the labour rate to suit the job. The output is a planning estimate that helps you judge the quotes you receive. It is not a fixed price.
How the formula works
The calculation adds two terms. The first is the wall area multiplied by the material rate per square metre of wall, plus the ceiling area multiplied by the material rate per square metre of ceiling. The second is the wall area multiplied by the labour rate per square metre of wall, plus the ceiling area multiplied by the labour rate per square metre of ceiling. The labour term is then multiplied by the labour multiplier r, and the material term is not. The formula is C_total = (A_w × m_w + A_c × m_c) + (A_w × h_w + A_c × h_c) × r.
The structure reflects how painting is actually priced. Materials scale with the amount of paint and primer you need, and that quantity follows the surface area directly. Labour also scales with area, but the rate per square metre differs between walls and ceilings because ceilings take longer to paint. The multiplier changes only the labour side, since paint is bought from the same retail and trade channels whatever the location of the job.
Edge cases in the inputs
Enter 0 for the ceiling area if you are not painting ceilings. The ceiling terms then drop out and the estimate covers the walls only. A multiplier of 1 applies the reference labour rate. Values above 1 raise the labour cost, for example for a condo with restricted working hours or difficult access, and values below 1 suit simple jobs with easy access and little preparation. Areas and rates should be positive. A negative area has no physical meaning, and a zero material rate removes the material cost from the total, which is only sensible if you already know the paint cost from another source.
Materials: what the material rate should cover
The material rate covers everything you have to buy, not just the paint. For walls, that means the paint itself, a primer where the surface is new plaster, bare concrete or heavily patched, filler for cracks and holes, sandpaper, painter's tape, rollers and roller sleeves, brushes, trays, and drop sheets to protect floors and furniture. Ceilings need the same list, plus ceiling paint, which is usually a flat finish that hides marks well.
Paint grade changes two things: the coverage per litre and the number of coats needed. A higher-grade paint may cover more area per coat and hide the surface with one fewer coat, but it only saves money if the manufacturer's technical datasheet confirms it. Check the datasheet for the coverage per litre and the recommended number of coats, then use those figures to work out the litres you need. The calculator does not do this step for you, because coverage varies by product and by surface.
In Singapore's humid climate, mould and mildew are a practical concern in bathrooms, kitchens and rooms with poor ventilation. A mould-resistant emulsion is often specified for these areas, and the cost difference should be built into the material rate rather than ignored. Tiled wet areas need a different approach altogether, because tiles are not painted with the same product as plaster.
Consumables are a small part of the total but easy to forget. A full flat needs more tape, sheets and sandpaper than most people expect, and running out halfway through a room can create colour differences between batches. Where possible, buy all the paint for one room from the same batch and note the batch number on the tin.
Labour: the most variable part
Labour is the part of a quote that changes most with the job and the contractor. Two things drive it: the time the work takes and the rate charged for that time. Time depends on the surface condition, the number of coats, the height of the ceiling and the access. The rate depends on the type of contractor and on market conditions at the time of the job.
Contractors fall into three broad groups. An individual painter often has the lowest labour rate, but may not issue a formal invoice or a written warranty, which makes a claim harder if the work is defective. A small registered company should provide an invoice, insurance details and a written warranty, and its rate reflects that accountability. A larger contractor with a project team and a fixed schedule sits at the upper end. None of these options is automatically the right one. The choice depends on the size of the job, how much supervision you can give and how important a formal warranty is to you.
Ceilings are slower to paint than walls for a simple reason: the work is done with the arms raised, the painter needs a platform or ladder, and the edges need more care to avoid drips and uneven coverage. A high ceiling, such as in a double-volume space or a landed house, takes more time again, because it may need scaffolding or a tall platform. In flats and condos with false ceilings, the relevant area is the visible surface of the false ceiling, not the floor area of the room beneath it, so the ceiling input should match what will actually be painted.
The labour multiplier lets you adjust the labour rate to the conditions of the job. Set it to 1 to use the reference rate. Raise it for a condo with restricted working hours, lift booking requirements, high floors where materials must be carried up, or limited access to the unit. Lower it only when the job is simple, the access is easy and the surfaces need little preparation.
Approvals, working hours and access
Painting is usually a simple decorating job, but it often sits inside a larger renovation. Hacking, wet works and structural changes can need approval before work starts, and the body that approves them depends on the type of property. For an HDB flat, the renovation rules and approvals are set by HDB. For a condominium, the management corporation sets its own rules on working hours, lift use and the protection of common areas, and may limit noisy works to set days and hours. Confirm the permitted hours and any approval before the contractor starts, because a delayed start can cost more than a lower quote saves.
Access also has a cost. If the contractor needs to move furniture, protect the lift, carry materials up several floors or work around occupied rooms, the labour time increases. Write these conditions into the quote so that the estimate and the quote describe the same job.
Doing the work yourself
DIY painting removes the labour cost but adds a cost in time, tools and finish quality. A single room is a reasonable project for a first-time painter with a few weekends available. A full flat is a much bigger task: moving furniture, filling holes, sanding, priming, applying two coats to every wall and ceiling, and cleaning up. Most people underestimate the time, and the results show most at corners, skirting boards, door frames and ceilings. The calculator's labour rate assumes a professional's speed. If you do the work yourself, the saving is real, but your time is not free, so decide what your time is worth before comparing the two options.
How to compare quotes
Get at least two or three quotes for the same specification. A useful quote states the number of coats, the paint type and grade, the wall and ceiling areas being charged, whether surface preparation such as filling, sanding and priming is included or charged separately, what protection is provided for floors and furniture, whether waste removal is included, and how GST is shown. GST rules are set by the Inland Revenue Authority of Singapore (IRAS), so check with IRAS if you are unsure whether a contractor must charge GST. Ask how many days the work will take and who will supervise it on site.
Ask the contractor directly how they prepare the surface. A contractor who explains the sanding, the filling and the primer in detail is more likely to deliver a durable finish than one who talks only about the paint. Before signing, check on the official public company register that the business is registered, and ask for a written warranty and details of its insurance.
If a quote is far above your estimate, ask what drives the difference. It is often the surface preparation, the access or the paint grade, and the answer shows which assumption to change in the calculator. If a quote is far below, check whether it excludes preparation, primer or a second coat, because those items are easy to leave out of a low price.
Common mistakes
The most common mistake is leaving out the ceilings or the false ceiling surfaces. The second is measuring the floor plan instead of the painted surface, which confuses the room area with the wall area. Owners also forget primer on new plaster, paint for door frames, grilles and window frames, and the consumables. Another common error is to treat a quote as final before a site visit. A contractor who has not seen the walls can only estimate what the surface will need.
Painting over damp, mould or peeling paint without finding the cause is the most expensive mistake, because the new paint will fail and the work has to be repeated. Diagnose the cause first. Once the surface is dry and sound, the calculator's figure is a much more reliable guide.
When not to use this calculator
Use it for interior painting of walls and ceilings in homes. It is not designed for exterior facades, which need access equipment, weather planning and different products, nor for specialist finishes such as textured coatings, metallic paints, limewash or decorative plaster, which have their own labour rates. It also does not cover wall tiling, which is a separate trade, or structural repairs. For the outside of a building, use a separate exterior estimate.
Limits of the estimate
The calculator gives a reasonable starting range based on the areas and rates you enter. It cannot see the walls, judge the condition of the plaster, estimate how many coats a dark colour change will need, detect old oil-based paint that must be removed, or account for the access on site. Treat the figure as a planning tool and a check against quotes, not as a binding price. Where the result and a quote differ significantly, the quote usually reflects site conditions that the calculator cannot know.
Frequently asked questions
How do I estimate the cost of painting a home in Singapore?
A 4-room HDB flat with about 120 m² of walls and 90 m² of ceilings has around 210 m² of painted surface per coat. Enter the wall and ceiling areas from your floor plan, choose who will do the work and the paint grade, then compare the estimate with the quotes you receive. The result is a planning figure. It does not replace a site visit by a contractor, because the final price depends on the condition of the surfaces, the access and the finish you choose.
Do ceilings cost more to paint than walls?
Usually yes. Painting a ceiling means working with the arms raised for long periods, so the work is slower and more tiring than painting walls. Ceilings are also harder to finish evenly, especially in rooms with a false ceiling, cove lighting or a high volume. For that reason the calculator applies a separate labour rate to the ceiling area. If you are not painting the ceilings, enter 0 for the ceiling area.
What is the difference between an individual painter and a painting company?
An individual painter often has a lower labour rate but may not issue a formal invoice or a written warranty. A registered company should be able to provide an invoice, insurance details and a written warranty, so its service cost is usually higher. A larger contractor with a project team sits at the upper end. For a small job, a reliable individual painter can be the sensible choice. For a larger project, a company with a clear schedule and a written warranty is often easier to hold to account.
Is it cheaper to buy the paint myself and hire only the labour?
It can be, but it depends on the contractor. A contractor may buy materials on terms that differ from a homeowner's, so the material price on a quote can be close to, or different from, what you would pay at a retail outlet. The real benefit of buying separately is choosing the exact paint you want, such as a specific finish or a mould-resistant emulsion, which the contractor may not normally stock. Check that the contractor accepts the paint you supply and whether the finish is still covered by their warranty.
When does DIY painting make sense?
DIY makes sense for a single room, a bedroom or a small feature wall, where the time is available and the budget is tight. A full flat takes many weekends of preparation, painting and cleaning, and the finish around corners, skirting boards and door frames usually looks better when done by an experienced painter. Remember to factor in your time and the cost of tools, which the material rate does not include.
When should I call a building professional before painting?
Call a building professional before painting if you see damp patches, mould, bubbling or large areas of peeling paint. Painting over a moisture problem only hides it for a while, and the paint will fail again. Structural cracks also need an assessment by a qualified engineer before the surface is repaired and painted. The calculator does not cover diagnosis or repairs, and the figure it gives assumes the surfaces are sound.
Related calculators
Wall Paint Calculator: How Many Litres Do You Need?
Calculate how many litres of wall paint a room needs, with a 5% allowance for touch-ups and an optional material cost estimate.
Ceiling Paint Calculator: Litres Needed
Calculate how many litres of paint your ceiling needs. Enter the dimensions, the paint coverage and the number of coats, and see the result instantly.
Exterior Paint Calculator for Building Facades
Works out the litres of exterior paint and primer a facade needs. Coverage adjusts to smooth, textured or porous surfaces, with a 10% margin.
View all Paint & Coatings calculators →
By RivoCalc · Reviewed under our editorial methodology · Updated 12 May 2026
This calculator gives an estimate for planning purposes only. Actual costs depend on the condition of the surfaces, the paint system, access, working hours and the contractor's rates, and they may differ from the result. Obtain itemised written quotes from contractors and check any approvals required before work starts.
