Ramp Slope Calculator: Percent, Degrees and Length
Calculates ramp slope in percent and degrees and the actual ramp length from rise and run, then checks the ADA 1:12 limit.
A ramp that rises 24 inches over 20 feet of horizontal run has a slope of 10%, or about 5.7 degrees, which is steeper than the 1:12 maximum that applies to ramps in public buildings. Checking the slope before any concrete is placed decides whether a ramp is usable, safe when wet, and able to fit the space available.
Ramp slope matters for any project that changes ground level, including garage entrances, front doors, sidewalk access, and doorways to storage areas. The slope determines whether wheelchair users, people with walkers, parents with strollers, and anyone moving heavy loads on a hand truck can use the ramp without strain. A ramp that is too steep is hard to climb and risky to descend when wet, while a ramp that is too flat may not fit the entrance at all.
This calculator works out three values from two measurements: the rise, which is the height difference between the lowest and highest points of the ramp, and the horizontal run, which is the length of the ramp measured on a plan. It returns the slope as a percentage, the angle in degrees, and the actual length of the ramp surface. It also indicates whether the slope meets the accessibility requirements.
The main US reference for ramps in public and commercial buildings is the 2010 ADA Standards for Accessible Design, section 405. Private single-family homes are generally outside that federal rule, but the same limits are a common reference for comfort and safety, and local codes may apply in every case. The sections below explain the formula, the ADA limits, and the mistakes that show up most often on site.
The explanation below uses US units; the calculator works in either system.
The result updates automatically.
Height difference between the low point and the high point of the ramp
Horizontal projection of the ramp — the length measured in plan
Ramp slope
- Slope angle
- 5.72 °
- Actual ramp length
- 32.96 ft
ADA compliance: Outside ADA accessibility range (8.3–15%) — requires technical review
How it works
Formula
How the calculation works
How to calculate ramp slope and what US accessibility rules require
A ramp built without a slope calculation is one of the most common and costly mistakes in small projects, and it is difficult to correct once the concrete has set. A ramp that is too steep can block wheelchair users and strollers, strain anyone pushing a load, and become slippery in rain. A ramp that is too flat can need more horizontal space than the entrance allows, or it can hold water on the surface if drainage is not planned.
The slope formula
The slope of a ramp is usually written as a percentage. Divide the rise (H) by the horizontal run (L), then multiply by 100. A ramp that rises 2 feet over a horizontal run of 20 feet has a slope of (2 ÷ 20) × 100 = 10%. The formula is written in metric units, and the calculator converts automatically, so you can enter feet and inches directly.
The angle in degrees is the arctangent of the rise divided by the run, converted from radians to degrees. For the same ramp, the arctangent of 0.10 is about 5.7 degrees. Percentages and degrees describe the same slope and are not interchangeable: a 100% slope is 45 degrees.
The actual length of the ramp surface is the hypotenuse of the right triangle formed by the rise and the run, calculated as the square root of (H² + L²). For the same ramp, the surface length is the square root of (2² + 20²), which is about 20.1 feet. On a 10% slope the surface is only about 0.5% longer than the horizontal run. The difference is small on gentle ramps, but it matters on steeper ones and for handrail and surface material lengths.
What the ADA requires for ramps in public buildings
The 2010 ADA Standards for Accessible Design, section 405, set the main requirements for ramps in public facilities such as shops, schools, and medical buildings. The key limits are:
- A maximum running slope of 1:12, meaning 1 inch of rise for every 12 inches of run. This equals 8.33%, or about 4.8 degrees.
- A maximum cross slope of 1:48 across the width of the surface.
- A maximum rise of 30 inches for any single run. At 1:12, a 30-inch rise needs a horizontal run of 30 feet before the first landing.
- A clear width of at least 36 inches between handrails or curbs.
- Level landings at the top and bottom of each run, at least 60 inches long in the direction of travel.
- Handrails on both sides of any ramp run with a rise greater than 6 inches or a horizontal projection greater than 72 inches.
- A surface that is stable, firm, and slip resistant.
Local codes and state laws can be stricter than the ADA, and the International Building Code (IBC) refers to the ICC A117.1 standard for accessible routes. Check both documents and any local amendments.
Private homes and residential ramps
Single-family homes are generally outside the ADA rules for public facilities. The International Residential Code (IRC) covers dwellings and has its own ramp provisions, which many states and cities amend. Even where the rules are not mandatory, the ADA limits are a widely used reference for comfort and safety.
Garage ramps and driveways are judged differently. Vehicle limits depend on ground clearance, the approach angle, and the length of the transition at the top and bottom of the ramp, not on the wheelchair limits. A basement garage ramp that drops 30 inches over 10 feet has a slope of 25%, or about 14 degrees. That is far above the ADA limit and unsuitable for a wheelchair user, but it can work for a car with carefully designed transitions.
Choosing the slope for the use
The right slope depends on who will use the ramp and what will move on it. For wheelchair users, the ADA maximum of 1:12 is the design limit, not a target. A gentler slope gives more margin, especially for a manual wheelchair user pushing up a long ramp without help. A 1:16 slope (about 6.25%) needs one third more horizontal run than 1:12 for the same rise. A 24-inch rise needs 24 feet of run at 1:12 and 32 feet at 1:16.
For loading ramps used with hand trucks, dollies, and pallet jacks, a flatter slope reduces the force needed to move the load. A ramp that visitors or people with disabilities may use should be designed to the public limits, even when it sits on private land.
Surfaces and finishes
The ADA requires a surface that is stable, firm, and slip resistant. On concrete ramps, a broom finish or grooves cut across the slope at regular intervals improve grip. The grooves should be shallow enough that they do not catch wheels or heels. Choose a finish with a published slip-resistance rating that covers wet conditions. Polished or troweled finishes become slippery when wet and are a poor choice for outdoor ramps.
Using the actual length in your planning
The actual length helps you plan the work in four ways:
- Surface area: multiply the actual length, not the horizontal run, by the clear width to estimate the concrete or finish area.
- Handrails: the rails follow the slope, so order them to the actual length plus any extensions the code requires at the top and bottom.
- Space: check that the horizontal run and both landings fit between the door and the property line or walkway.
- Drainage: a ramp that drops toward a wall or a door needs a planned drainage path.
Common mistakes
- Measuring the slope length instead of the horizontal run. The slope length is always longer, so it makes the ramp look gentler than it is. The error is small on gentle ramps and grows as the slope gets steeper.
- Entering the rise in inches and the run in feet without selecting the matching unit for each field.
- Treating the percentage as degrees. An 8.33% slope is about 4.8 degrees, not 8.33 degrees.
- Forgetting the landings, which add horizontal length that is not part of the slope.
- Ignoring the surface. A slope that meets the numbers can still be unsafe if the finish is slippery.
When not to use this calculator
This calculator gives the geometry of a ramp only. It does not design the structure, slab, reinforcement, retaining walls, or load capacity, which need a qualified professional. It also does not replace a site survey, because the ground may not be level or straight, and it does not evaluate stairs, curb cuts, or the transitions between a ramp and a sidewalk.
Summary
Enter the rise and the horizontal run, then read the slope, the angle, and the actual length. Compare the slope with the 1:12 limit if the ramp serves the public, and plan the landings, handrails, and surface around the result.
Frequently asked questions
What is the maximum slope for an accessible ramp in the United States?
For ramps in public and commercial buildings, the 2010 ADA Standards for Accessible Design (section 405) set a maximum running slope of 1:12. That means 1 inch of rise for every 12 inches of horizontal run, which equals 8.33% or about 4.8 degrees. A single run can rise no more than 30 inches before a landing, and landings must be at least 60 inches long. Private homes are generally outside this federal rule, but local codes can apply, so check with your building department before you build.
How do I calculate the slope of a ramp as a percentage?
Divide the rise by the horizontal run and multiply by 100. The rise is the height difference between the lowest and highest points of the ramp, and the run is the horizontal length measured on a plan, without counting the slope. For example, a ramp that rises 2 feet over 20 feet of run has a slope of (2 ÷ 20) × 100 = 10%. Both measurements must be in the same unit for the ratio to work, and the calculator handles unit conversion if you enter values in feet or inches.
What is the difference between slope in percent and angle in degrees?
A percentage expresses the rise divided by the run, multiplied by 100. An angle in degrees is the arctangent of that same ratio. A 10% slope is about 5.7 degrees, a 1:12 slope (8.33%) is about 4.8 degrees, and a 20% slope is about 11.3 degrees. On gentle ramps the two numbers look close, but they measure different things and are not interchangeable. A 100% slope is 45 degrees, so the gap grows quickly on steep ramps.
How do I find the actual length of a ramp?
The actual length is the diagonal of the right triangle formed by the rise and the run. Use the formula length = √(rise² + run²). For a ramp with a 2-foot rise and a 20-foot run, the length is √(2² + 20²) = √404, or about 20.1 feet. On a 10% slope the surface is only about 0.5% longer than the horizontal run, but the difference grows on steeper ramps and affects handrail and surface material orders.
Do I need a handrail on a ramp?
For ramps in public buildings, the ADA requires handrails on both sides of any ramp run with a rise greater than 6 inches or a horizontal projection greater than 72 inches. The handrails must also meet requirements for height, grip shape, and extensions at the top and bottom. Residential ramps are governed by the International Residential Code (IRC) and local amendments, which can set different thresholds, so confirm the rule with your local building department before you install one.
How far does a ramp need to extend to reach a given height?
At a 1:12 slope, a ramp needs 12 inches of horizontal run for every inch of rise. A 30-inch rise therefore needs a run of 30 feet, and 30 inches is the maximum rise for a single run, so a taller rise needs an intermediate landing. A 24-inch rise needs 24 feet of run at 1:12, or 32 feet at a gentler 1:16 slope. Plan the space for the full run plus the landings at the top and bottom, because the landings add length that is not part of the slope.
See all Measurements & Quantities calculators →
By RivoCalc · Reviewed under our editorial methodology · Updated July 1, 2026
This calculator gives a geometric result for planning only. It does not replace a site survey, a structural design, or the requirements of the ADA, the IBC, the IRC, and the codes adopted by your state or city. Confirm the final slope, width, landings, handrails, and surface with your local building department or a licensed design professional before you build.
