Skip to main content

Brick Calculator: How Many Bricks per m²?

Calculates the clay bricks needed for a wall, with mortar joint and waste allowance included. Optional material cost estimate.

A wall 4.0 m long and 2.4 m high needs 512 clay bricks once a 10% waste allowance is added, or 466 bricks before any waste. The figures assume a 230 × 76 mm brick face and a 10 mm mortar joint, so each brick covers 0.02064 m² of wall, or about 48.4 bricks per square metre before waste.

The count depends only on the size of the visible brick face and the thickness of the mortar joint. The depth of the brick, which sets the thickness of the finished wall, does not change how many bricks you need per square metre. Depth matters for insulation, acoustic performance and how the wall is tied to its frame, but not for the count. The calculator applies one formula to the wall area, the brick face and the joint, and rounds the result up to a whole brick.

The mortar joint is the step most often missed. A 10 mm joint looks small, but it adds about 18% to the wall area that each brick covers. Leaving it out treats every brick as covering less wall than it does, so the same wall would appear to need 605 bricks instead of 512, and you would order far more than the job requires. Joint thickness is set by the project specification and by bricklaying practice, so confirm the figure with the designer or the bricklayer before ordering. The calculator uses 10 mm as its worked example.

Enter the wall length and height, the brick face dimensions, the joint thickness and the waste allowance, and the calculator returns the total number of bricks, rounded up. It suits brick veneer walls, internal partitions, garden walls and infill panels, in solid or cored clay brick. Double brick walls have two leaves, so calculate each leaf separately. A price per brick gives an estimate of material cost, but prices vary by product, region and order size, so treat it as a starting point for quotes.

The result updates automatically.

Typical ceiling height: 2.5–2.7 m (flat); up to 3.0 m (house) (about 8.2–8.9 ft; 9.8 ft).

Standard hollow brick: 30 cm · Acoustic brick: 37 cm (about 11.8 and 14.6 in)

Standard hollow brick: 20 cm · Thermal brick: 19 cm (about 7.9 and 7.5 in)

Typical on-site value: 1 cm (about 3/8 in)

Plain wall: 5% · With cut-outs and openings: 10%

Bricks needed

218bricks

for a wall of 13.5

Wall area
13.50 m²
Bricks per unit area
15.4 unid./m²
Effective area per brick
651 cm²

Turn this calculation into a quote for your client

We're building a tool for professionals. Be among the first to try it.

Share

How it works

1

Enter the wall length and height in metres. For a wall with windows or doors, use the net area after subtracting the openings.

2

Enter the brick face dimensions. The worked examples use 230 × 76 mm, so confirm the face size on the product data sheet of the brick you are buying before ordering.

3

Set the mortar joint thickness. The worked example uses 10 mm; use the figure in the project specification if it differs.

Formula

N = ⌈(A × (1 + D/100)) / ((L + J) × (H + J))⌉
N — Number of bricks required, rounded up to a whole brick
A — Wall area (m²) = length × height
D — Waste allowance (%)
L — Brick face length (m)
H — Brick face height (m)
J — Mortar joint thickness (m), set by the project specification; the worked example uses 0.01 m (10 mm)

How the calculation works

How many bricks does a wall need?

Brick veneer is a common way to build houses in Sydney, Melbourne, Brisbane, Perth and Adelaide, and many owner-builders and renovators work out their brick order themselves. The arithmetic is simple, but one detail catches people out: the mortar joint. Ignoring the 10 mm of mortar between bricks can change the count by close to a fifth, and the mistake only shows up when the bricks run out before the wall is finished.

The formula and what goes into it

The calculation divides the wall area by the effective area of one brick, including its joint, and rounds the result up to the next whole brick. The formula is N = ⌈(A × (1 + D/100)) / ((L + J) × (H + J))⌉, where each letter stands for one input.

Take a wall 4.0 m long and 2.4 m high, so A is 9.6 m². Each brick with its joint occupies (0.230 + 0.010) m × (0.076 + 0.010) m, which is 0.240 m × 0.086 m, or 0.02064 m². Without waste, 9.6 ÷ 0.02064 = 465.1, rounded up to 466 bricks. With a 5% allowance the area becomes 10.08 m² and the result is 489 bricks. With 10%, the area becomes 10.56 m², which gives 511.6 and so 512 bricks.

The joint is added to both dimensions because each brick repeats across the wall at its length plus one joint, and up the wall at its height plus one joint. Rounding is always upward. A short delivery stops the work, and a few spare bricks cost far less than a second trip to the supplier.

Brick dimensions and the worked example

The worked example uses a brick face of 230 × 76 mm, laid as a stretcher, which is the face that shows on the outside of the wall. It is an illustrative size for the arithmetic, not a dimension that applies to every product. AS/NZS 4455 covers the masonry unit itself, so the requirements a unit must meet are set out in that standard, and the product data sheet gives the figures for the brick you are buying. The depth of the brick, which runs into the wall, varies by product, and it sets the thickness of the finished wall. Measure a sample of bricks and check the data sheet before ordering a full pallet, because over a large wall small differences add up.

Cored bricks have holes through the body, which makes them lighter and easier to handle. Solid bricks have no cores and are heavier, and they are chosen where higher compressive strength or a particular finish is required. Both have the same face, so the count per square metre is identical. The difference lies in weight, cost per unit and the performance of the finished wall.

The wall type also changes what you count. In single-leaf brickwork the wall is one row of brick. In brick veneer, the outer brick leaf is tied to a timber or steel frame behind a cavity, and only the outer leaf needs counting as brick. In double brick, the wall has two leaves of brick tied together, so each leaf is calculated separately and the two counts are added. Joint thickness is left to the project specification and to bricklaying practice, as the next section explains.

Why the mortar joint matters

Each joint takes up space that would otherwise be wall, so it has to be counted in the module. In the example above, each brick and its joint covers 0.02064 m², compared with 0.01748 m² for the brick face alone. That 18% gap is the difference between an accurate order and one that is far too large.

Joint thickness also affects the finished wall. Joints much thinner than 10 mm are harder to lay consistently with irregular bricks and demand more care from the bricklayer. Thicker joints use more mortar, make the wall look coarser and reduce the efficiency of the brickwork. Horizontal bed joints and vertical perpend joints are normally laid to the same thickness, so a single figure works for both.

If the joint varies across the wall, the count set by the calculation will no longer match what is laid. The waste allowance absorbs small variations, but a wall with consistently thick joints can run short.

Waste allowance

The waste allowance covers cut bricks at corners, around window and door openings, at lintel and sill levels, bricks broken in handling, and the half and quarter bricks that a bond pattern requires. A simple rectangular wall with few openings can use about 5%. A wall with many openings, pier intersections, service penetrations or a lot of cutting needs about 10%. Irregular work, such as a new wall that ties into an older one, may need more, and a bricklayer's estimate is the best guide.

Spare bricks are worth keeping after the job. Batches of clay brick vary in colour and size, and a spare stock makes repairs and later additions much easier to match.

Common mistakes

  • Leaving out the mortar joint. This overstates the count by about 18% in the example above, so you buy bricks the wall does not need.
  • Skipping the waste allowance. The last course usually needs cut bricks, and the job is left short.
  • Ordering the exact count. A spare 5 to 10% covers breakage, cutting errors and repairs.
  • Using the single-leaf count for a double brick wall. Each leaf needs its own calculation.
  • Counting openings as wall. Subtract windows and doors from the wall area before calculating, otherwise the order is too large.
  • Mixing units. Entering millimetres in a field that expects metres gives a result that is wildly wrong, so check every input before trusting the total.

When not to use this calculator

This calculator suits quantities for simple, single-leaf walls such as internal partitions, garden walls and infill panels. It does not size structural walls. Any wall that carries loads from a roof, floor, beam or upper storey needs a structural design by a qualified engineer. Masonry design in Australia follows AS 3700 Masonry structures, and design actions such as wind and earthquake loads follow the AS 1170 series. Retaining walls, parapets and walls that need fire separation also require specific design.

Most building work needs approval from the local council or a private building certifier. The National Construction Code applies, with state and territory variations, and Volume Two covers houses. Check those requirements before you order materials for any wall that will be inspected. The calculator gives the quantity; it does not confirm that a wall meets the code.

Frequently asked questions

How many bricks do I need per square metre of wall?

With a clay brick face of 230 × 76 mm and a 10 mm mortar joint, each brick covers about 0.0206 m² of wall. That gives about 48.4 bricks per square metre before waste. Adding a 5% allowance brings the figure to about 51 bricks per square metre, and a 10% allowance to about 53. Those numbers are useful for a quick estimate, but the full calculation is more accurate because it rounds the total for the whole wall and uses the real wall dimensions. Check the actual brick dimensions on the product data sheet, because a different face size changes the result.

Which brick face size should I enter in the calculator?

Enter the face dimensions printed on the product data sheet of the brick you are buying, because the face size belongs to the product. The worked examples here use 230 × 76 mm for the arithmetic. AS/NZS 4455 covers masonry units themselves. The depth of the unit sets the wall thickness, and it varies by product, so choose the depth against the project specification, the insulation and acoustic requirements, and the services that will run inside the wall. The building designer's details will confirm the choice.

What waste allowance should I use for bricks?

Use about 5% for a simple rectangular wall with few openings, and about 10% for a wall with several windows or doors, service penetrations, corners or a lot of cut bricks. Walls with arches, curves or irregular connections to an existing structure need a higher allowance, and the bricklayer's estimate is a useful check. Spare bricks kept after the job are separate from the waste allowance and cover repairs later. The calculator uses the allowance as a percentage of the wall area, so enter the figure as a whole number such as 10 for 10%.

What is the mortar joint and what thickness is correct?

The mortar joint is the layer of mortar between bricks, both the horizontal bed joints and the vertical perpend joints. The worked examples here use 10 mm. The project specification sets the actual thickness, and AS 3700 Masonry structures is the design standard for structural masonry. Thinner joints are harder to lay consistently and demand more accuracy, while thicker joints use more mortar and make the wall look coarser. Enter the joint in metres in the calculator, so 10 mm becomes 0.01.

What is the difference between solid and cored bricks?

Solid bricks have no holes through the body and are heavier, with higher compressive strength, which suits some structural and paving uses. Cored bricks have holes through the body, which makes them lighter and easier to handle, and they change the thermal and acoustic behaviour of the wall. For the calculator the difference does not matter, because the count depends only on the face dimensions and the joint. A solid and a cored brick with the same face size need the same number of units per square metre. The choice affects weight, cost and how the wall performs.

When do I need an engineer or a building certifier for a brick wall?

A structural engineer should design any wall that carries loads from a roof, floor, beam or upper storey, as well as retaining walls and walls that need fire separation. Most building work also requires approval from the local council or a private building certifier, who will apply the National Construction Code (ncc.abcb.gov.au). This calculator is suitable for estimating quantities for simple internal partitions and garden walls. It does not check structural adequacy and does not confirm compliance with the code. Masonry design follows AS 3700 Masonry structures, and loads are set out in the AS 1170 series.

Related calculators

View all Measurements & Quantities calculators →

By RivoCalc · Reviewed under our editorial methodology · Updated 4 June 2026

Results are estimates for single-leaf brick walls with uniform joints. They do not replace a structural design by a qualified engineer or the requirements of the local council or building certifier.