Skip to main content

Sand and Cement Mortar Calculator

Calculates the number of cement bags and the sand volume for mortar from the area, layer thickness, mix ratio and bag weight.

For plastering 15 m² of internal wall 1.5 cm thick in a 1:4 mix, you need 4 bags of 20 kg cement and about 0.19 m³ of sand, with the 10% allowance for site wastage included. The same area laid as a 5 cm screed needs 14 bags and about 0.64 m³ of sand, because thickness sets the volume and the materials scale with it.

The mix ratio sets the strength of the mortar and is the input that changes the quantities most. A 1:4 mix (one part cement to four parts sand, by volume) is a common general-purpose choice for internal plaster and laying masonry. A 1:3 mix suits exterior render and surfaces that are often wet, because it is the stronger of the usual mixes. Many Australian masonry and render jobs also use lime in the mortar, which this calculator does not cover.

The European standards EN 998-1 (rendering and plastering mortars) and EN 998-2 (masonry mortars) describe mortar types, while masonry design in Australia sits within the National Construction Code and the AS 3700 masonry standard. Your specification or the product data sheet has the final say on the mix.

Enter the area, the layer thickness, the mix ratio and the weight of your cement bags. The calculator returns the number of bags, rounded up, and the matching volume of sand. If you also enter the price of bags and sand, it estimates the material cost.

Treat the result as a planning figure. Waste, sand moisture and uneven surfaces change the real quantity, so order with a small margin and check the figures against the plan.

The result updates automatically.

1 cm bedding · 1.5–2 cm render · 4–7 cm screed

A standard bag of cement typically weighs 25 kg.

Bags of cement

325 kg bags

for 0.150 m³ of mortar (10% allowance included)

Mortar volume
0.150 m³
Sand needed
0.16 m³
Safety margin
10% included

Turn this calculation into a quote for your client

We're building a tool for professionals. Be among the first to try it.

Share

How it works

1

Enter the area to be covered in square metres.

2

Set the layer thickness in centimetres, using the value from the specification for the job. The examples on this page use 1.5 cm for plaster and 5 cm for a screed only to show the arithmetic.

3

Choose the mix ratio for the job: 1:4 is the common general-purpose choice, and 1:3 suits exterior render and wet surfaces.

Formula

N = ⌈(A × e/100 × C × 1,10) / P⌉
N — Number of cement bags (rounded up)
A — Area to be covered (m²)
e — Thickness of the mortar layer (cm)
C — Cement per m³ of mortar (kg/m³), depending on the mix ratio
P — Weight of one cement bag (kg)
1,10 — Allowance factor of 1.10, which adds 10% for site wastage

How the calculation works

How to calculate sand and cement for mortar

Mortar is the material that bonds, levels and protects. Whether you are laying bricks, plastering a wall or laying a screed over a slab, it is a mix of cement, sand and water in set proportions. Getting the quantities right before you order avoids two common problems. The first is leftover cement, which absorbs moisture and goes off if it is stored too long. The second is running out halfway through a wall or a screed, which leaves an awkward joint and a second delivery to organise.

This calculator works out the number of cement bags and the volume of sand for a flat layer of mortar. It is built for planning: it gives you a sensible order quantity for internal plaster, brick joints, screeds and general mortar work on residential jobs.

What the mix ratio does

The mix ratio is the proportion of cement to sand, measured by volume. On site, mortar is proportioned with buckets, shovels or a barrow, not with scales. The common ratios are these:

  • 1:3 (one part cement to three parts sand): the stronger and denser of the common mixes. It suits exterior render, the lower parts of external walls and surfaces that are often wet.
  • 1:4 (one part cement to four parts sand): the most versatile of the common mixes. It is used for bricklaying, internal plaster and light screeds, and it suits most general residential work where the specification does not call for a particular mix.
  • 1:5 (one part cement to five parts sand): a leaner mix for internal plaster in rooms with no particular strength demands. It uses less cement but gives less strength and bond.
  • 1:6 (one part cement to six parts sand): used for fill, levelling and low-stress work. It is not suitable for structural masonry or exposed render.

Many Australian masonry and render jobs use lime alongside cement, for example a cement, lime and sand mix. This calculator covers cement and sand only. If your specification calls for lime, the cement quantity from this calculator will not match it, so check the mix with your builder or engineer before ordering.

The European standards EN 998-1 (rendering and plastering mortars) and EN 998-2 (masonry mortars) describe mortar types and their properties. In Australia, the National Construction Code, published by the Australian Building Codes Board, sets the performance requirements for housing, and masonry is designed to the AS 3700 masonry standard. Each state and territory can add its own variations to the Code, so check local requirements before you start.

How to calculate the volume

The base of the calculation is the volume of the layer, which is the area multiplied by the thickness. A 15 m² room with a 5 cm screed holds 15 × 0.05 = 0.75 m³ of screed. A wall that is 3 m long and 2.5 m high has an area of 7.5 m². Plastered 1.5 cm thick, it holds 7.5 × 0.015 = 0.11 m³ of mortar.

The layer thickness depends on the type of work and on the specification for the job, so the specification always takes priority. The thicknesses used in the examples on this page, 1.5 cm for plaster and 5 cm for a screed, are worked-example values that show the arithmetic. They are not recommended thicknesses.

The calculator adds a 10% allowance to the calculated volume. The reason is practical. The thickness of a plaster coat or a joint is never perfectly even. There are thicker spots, corners and irregular surfaces, and some mortar is always lost during application. A 10% margin covers most ordinary jobs. If the surface is very uneven, or the wall has large openings, check the result against the plan and allow a little more.

The cement quantity follows from the volume. For a 1:4 mix the calculator uses about 320 kg of cement per cubic metre of mortar. Multiplying the volume by 320 and by the allowance gives the cement mass, and dividing that mass by the bag weight gives the number of bags. The result is then rounded up, because you cannot buy part of a bag.

The sand volume is estimated as the total mortar volume less the space the cement takes up. For the plaster example, the mortar is 0.25 m³ and the cement occupies roughly 0.06 m³, which leaves about 0.19 m³ of sand. For the 5 cm screed on the same area, the mortar is 0.825 m³ and the cement occupies roughly 0.18 m³, which leaves about 0.64 m³ of sand. This is an estimate. Sand volume changes with its moisture content and grading, so allow a little extra when ordering.

The bag weight matters more than many people expect. Take the 15 m² plaster example at 1.5 cm. The cement mass is about 79 kg, which needs 4 bags whether they weigh 20 kg or 25 kg. The 5 cm screed on the same area needs about 264 kg of cement. That is 14 bags of 20 kg but only 11 bags of 25 kg. Always set the bag weight to match the label on the product you intend to buy.

Cement and sand supply in Australia

General-purpose cement is the usual choice for general mortar work. It is sold in bags at building suppliers and hardware stores, and for larger jobs it can be ordered in bulk. Bags of 20 kg are common in Australia, but always check the label, because the bag count depends directly on the weight.

Sand comes in several types, and the right one depends on the job:

  • Plastering sand: a fine, washed sand used for internal plaster and for render. It gives a smooth finish and is easy to work.
  • Bricklaying sand: a washed sand, usually a little coarser than plastering sand, used for joints between bricks and blocks.
  • Crushed or manufactured sand: made from crushed rock, with angular grains. The grains can give a better grip for render, but the mix can feel harder to work, so test a small batch first.

For volumes of about half a cubic metre or more, buying bulk sand from a quarry or landscape supplier is usually cheaper per cubic metre than buying bagged sand. Pre-blended dry mortar bags from building suppliers are convenient for small repairs, or when you cannot mix on site, but they cost considerably more per cubic metre than mixing cement and sand yourself. Enter the current prices in the calculator to compare the options for your job.

Common mistakes to avoid

Confusing volume ratios with weight ratios. On site, mixes are proportioned by volume. Some technical data sheets give mixes by weight, and the two give different results, because cement and sand have different bulk densities and moisture contents. Check which basis the data sheet uses before you copy the ratio into the calculator.

Using dirty or poorly graded sand. Sand that contains a lot of clay or silt needs more cement to reach the same strength, and the effect can be significant. Ask the supplier where the sand comes from and how it is graded, and test a small batch before mixing a large one. Sand from different quarries varies, sometimes a lot, even within the same state.

Adding too much water. A very wet mortar is easy to spread, but it loses strength. Use the least water that still lets you work the material. A good mortar holds its shape on the trowel and does not slump off the board. If it runs, it has too much water.

Not curing the work. Cement mortar needs moisture to gain strength. In hot, dry or windy weather, mist the render or screed with water for the first few days, so it does not dry too quickly and crack.

When not to use this calculator

The calculator is for quantities of ordinary mortar. It is not the right tool in these cases:

  • Structural concrete, such as slabs, columns, beams and footings. Those need a concrete calculation designed to AS 3600, which includes coarse aggregate.
  • Load-bearing masonry design, where the wall, its mortar and its ties must be designed by an engineer.
  • Proprietary render or waterproofing systems, which must follow the manufacturer's data sheet for the mix, the coat thicknesses and the curing.
  • Work that needs a building permit, or that affects the structure of a building.

When to get professional advice

Plastering an internal room or laying a short run of brick joints is manageable for many people with some experience. Exterior render on a building, work that affects the structure, rising damp, persistent water ingress and any work that needs a building permit should be checked by a licensed building practitioner or a structural engineer. Building work in Australia is regulated under the National Construction Code, published by the Australian Building Codes Board, and each state and territory adds its own variations. Check with the relevant state or territory building authority before starting work that needs approval.

Use the calculator as a starting point for your order, then check the figures against the plan and the specification before you buy.

Frequently asked questions

How many bags of cement do I need to render 10 m²?

For 10 m² at 1.5 cm thick in a 1:4 mix, the volume is 0.15 m³. With the 10% allowance, the mortar volume becomes 0.165 m³, which needs about 53 kg of cement at 320 kg per cubic metre. With 20 kg bags, that is 3 bags, rounded up. The sand is about 0.13 m³, which is the mortar volume less the space the cement takes up. Check the weight on your bags before you order, because the bag count depends on it.

What mix ratio should I use for bricklaying?

A 1:4 mix (one part cement to four parts sand, by volume) is a common general-purpose choice for bricklaying on internal walls and in dry areas. For exterior walls or surfaces with more exposure to water, a 1:3 mix is the stronger option. The joint thickness comes from the design, so enter the value from the specification. Where the design calls for lime or a specific mortar class, follow the specification instead, and check the requirements in the AS 3700 masonry standard.

What is the difference between mortar and concrete?

Mortar is a mix of cement, sand and water, with no coarse aggregate. It is used for bricklaying, render, plaster and screeds. Concrete includes coarse aggregate, such as gravel or crushed rock, and is used for structural elements like slabs, columns and footings. Concrete structures are designed to the AS 3600 standard. In practical terms, mortar is for finishes and masonry joints, and concrete is for structure.

When should I use a 1:3 mix instead of 1:4?

Use a 1:3 mix for exterior render that is exposed to rain and wind, and for the lower parts of external walls and other surfaces in frequent contact with water. The 1:4 mix is suitable for most internal plaster and bricklaying in dry areas. A richer mix is stronger but uses more cement, so choose it only where the exposure or the specification requires it.

When is pre-blended dry mortar better than mixing on site?

Pre-blended dry mortar in bags suits small repairs, jobs where no mixer is available, or cases where you need a fixed mix from the manufacturer. It costs considerably more per cubic metre than mixing cement and sand yourself. For larger jobs, mixing on site is usually more economical. Check current prices at building suppliers before you decide, and enter them in the calculator to compare.

What is the correct thickness for internal plaster in Australia?

There is no single correct thickness. The thickness comes from the specification or design for the job and depends on the wall and the plaster system used. The 1.5 cm (15 mm) figure in this calculator's example is a worked value to show the arithmetic, not a recommended thickness. Thicker coats raise the risk of shrinkage cracking as they dry, and very thick coats may need reinforcing mesh, so confirm the build-up in the specification before ordering.

When should I get a professional to check mortar work?

For plastering an internal room or laying a short run of brick joints, this calculator is enough for ordering. For exterior render on a building, work affecting the structure, rising damp, persistent water ingress or any work that needs a building permit, a licensed building practitioner or a structural engineer should check the design. Building work is regulated under the National Construction Code, and approval rules vary by state and territory, so check with the relevant building authority before starting.

Related calculators

View all Structure & Materials calculators →

By RivoCalc · Reviewed under our editorial methodology · Updated 3 June 2026

Results are estimates for planning material orders. Real quantities depend on site conditions, waste, sand moisture, surface irregularities and the product specification. For structural, load-bearing or regulated work, confirm the mix with a licensed building practitioner or a structural engineer before you start.