Roof Tile Calculator: How Many Tiles Per m²
Works out the number of roof tiles for a pitched roof in Marseille, pan-and-cover, Roman or plain profiles, with a wastage allowance.
To cover 60 m² of pitched roof with Marseille tiles, at a planning yield of 16 pieces per m² and a 10% wastage allowance, you need 1,056 tiles. The same roof in pan-and-cover tiles, using an example yield of 13 pieces per m², needs 858 pieces, roughly 19% fewer.
The tile profile matters for more than looks. Yield per square metre varies widely between profiles: a larger profile needs far fewer pieces per m² than a small plain tile, and that figure decides how many boxes or pallets you order. This calculator covers four clay profiles, Marseille, pan-and-cover, Roman and plain, and fills in a planning yield for each one. For concrete tiles or any other product, select Custom and enter the yield from the manufacturer's data sheet.
Enter the real sloping area of the roof, not its footprint on the plan. A roof with a 30% pitch has a sloping surface about 4.4% larger than its plan area, and at 45% it is about 9.7% larger. On a house with an 80 m² footprint, that gap is between about 3.5 m² and 8 m², enough to leave one or two courses short on the last section of roof. Enter the tile type and a wastage allowance, and the calculator returns the total number of pieces, rounded up to a whole tile.
The result is only as good as the inputs. If the roof has several planes, hips or valleys, measure each plane separately and use a wastage allowance of 15% or more to cover the extra cuts at those junctions. Keep the batch number of the tiles you order, because tiles from different production runs can differ slightly in size and colour.
The rest of this page explains how to measure the sloping area, how to choose the allowance and when to bring in a roofing professional.
The result updates automatically.
The actual sloped surface area, not the plan (footprint) area
Typical value for the selected roof tile type
10% for simple roofs; 15% for roofs with multiple pitches or complex ridge lines
Check the unit price with your supplier for the model you've chosen
Roof tiles needed
includes 128 pieces of waste allowance
- Roof area
- 80.0 m²
- Coverage rate
- 16 pieces
- Tiles before allowance
- 1,280 pieces
How it works
Formula
How the calculation works
How many roof tiles do I need?
Re-roofing or building a new roof is one of the largest jobs on a house, both for protection and cost. Working out the tile count properly before you order saves money and avoids running short halfway through the job, when the batch you need may no longer be in stock. The base formula is simple: multiply the roof area by the tile yield in pieces per square metre, then add a wastage allowance. What makes the calculation tricky, and why many people get it wrong, is using the plan area (the footprint of the roof seen from above) instead of the true sloping area.
For a 30% pitch, the sloping area is about 4.4% larger than the plan area. At 45%, it is about 9.7% larger. On a house with an 80 m² footprint, that gap is roughly 3.5 m² at 30% and nearly 8 m² at 45%, which can be enough to leave one or two courses of tiles short on the last section of roof.
Tile types and their yields
The calculator covers four common clay profiles. Each one has its own yield in pieces per square metre, and the yield changes the total count far more than the wastage allowance does. The planning values pre-filled in the calculator are a starting point only. Replace them with the figure from the manufacturer's data sheet for the product you buy, because cover width and overlap differ between ranges.
Marseille tile: a rectangular profile with a mechanical interlock between pieces. It is quick to lay and easy to align, which is why it is the usual choice for new builds.
Pan-and-cover tile: a curved profile made of two pieces, a channel (the pan) and a cover. It has a traditional look that suits older and heritage homes. It takes longer to lay than Marseille-type profiles, and it needs a steeper pitch so that water can drain between the pan and the cover.
Roman tile: similar in shape to the Marseille tile but with a softer, more rounded profile. It suits Mediterranean-style homes.
Plain tile: a small, flat tile with an understated look, often found in heritage and traditional designs. Each piece is small, so a square metre needs many more pieces, and the piece count and the number of boxes to order are much higher even though the profile is simple to lay.
On new builds, Marseille-type profiles are often chosen because they are quicker to lay and align. Pan-and-cover profiles tend to appear in restorations and heritage work, where the look is specified by the design or required by the council.
Measuring the true roof area
The area that matters for tile counting is the sloping surface, not the plan. Take one plane of a gable roof: 10 m long along the eaves, with a 5 m horizontal run from eave to ridge, at a 35% pitch. The rise over that run is 35% of 5 m, or 1.75 m, so the true width of the plane is √(5² + 1.75²) ≈ 5.30 m. The real area of that plane is about 10 × 5.30 = 53 m², instead of the 50 m² shown on the plan. A gable roof has two such planes, so measure and add each one.
If you know the plan area and the pitch but not the sloping area, use this conversion:
Real area = Plan area × √(1 + (pitch in % / 100)²)
For a gable roof with an 80 m² plan area at 35%, the real area is about 80 × 1.059 ≈ 85 m². The formula assumes one uniform pitch. For roofs with several planes at different pitches, convert each plane separately and add the results.
For a re-roof, a roofer can measure the area on site. For a new home, the plans or the roof framing schedule should show the area of each plane. Check these figures before ordering, because a small error in the area moves the whole count.
Wastage allowance and rounding
A 10% allowance suits simple, rectangular roofs with no interruptions. Roofs with several planes, hips, valleys or dormers typically need 15%. Irregular roofs, or roofs on older homes with non-rectangular plans, may need 20%.
The allowance covers three sources of loss: cuts along the edges (especially at the gable ends), breakages during delivery and laying, and a reserve for future repairs. Keeping 10 to 15 spare tiles in storage is worth more than having to find the same profile years later. Tiles from different production runs can differ slightly in size and colour, and the difference often shows after several years in the sun and rain. Buy the whole order from one batch where possible.
The formula rounds the result up to a whole piece, shown by the ceiling brackets. Tiles are usually sold in boxes or pallets, so round up again to the box quantity your supplier sells.
When to use this calculator, and when not to
The calculator suits early budgeting and checking a roofer's quote. It does not replace a roof design. It is also not the right tool for roofs covered with sheet metal, membranes or shingles, which use different overlaps and are counted in different units. For concrete tiles or other products with a different cover width, select Custom and enter the yield from the manufacturer's data sheet, not the clay profile default.
Common mistakes
The most frequent error is using the plan area instead of the sloping area, which leads to ordering too few tiles. The second is forgetting the wastage allowance, or cutting it below 10% on a complicated roof. The third is using a yield value from one profile for another. Pan-and-cover and Marseille profiles have different yields, and that difference alone can change the order by a large margin. The fourth is ignoring the minimum pitch: a profile laid on a roof flatter than the manufacturer allows can leak at the joins even with the correct tile count.
When to bring in a roofing professional
For a full re-roof or a new roof, use a licensed roof tiler or builder with roofing experience. They will check the roof framing (battens, rafters or trusses, and the wall plate), the underlay or sarking, the correct laying and interlock of the tiles, and the flashings at ridges, valleys and eaves. Quotes for the same job can differ a lot, so compare the tile count and wastage allowance each quote uses.
Local rules also apply. The National Construction Code (NCC) Volume Two covers houses (Class 1 and Class 10 buildings), with variations by state and territory. Confirm the requirements with your local council or building surveyor before work starts. Homes in heritage overlay areas usually need council approval before the roof form or tile profile changes, and the council may specify the profile itself.
Roof tiles sold in Australia are commonly specified against AS 2049, the Australian Standard for roof tiles, which is a useful reference when comparing product data sheets. For older homes, inspect the existing framing before starting, since it may need repair before new tiles go on.
Frequently asked questions
How many roof tiles do I need for 100 m² of roof?
Using example planning yields: Marseille tiles at 16 pieces per m² with a 10% wastage allowance give 100 × 16 × 1.10 = 1,760 tiles. Pan-and-cover tiles at 13 pieces per m² give 1,430 tiles. Plain tiles at 48 pieces per m² give 5,280 tiles. These figures assume 100 m² of sloping surface, not plan area. Enter your real sloping roof area into the calculator for an exact count, and check the yield against your manufacturer's data sheet.
How many pan-and-cover tiles are needed per m²?
Pan-and-cover tiles are sold as a channel (pan) and a cover, and the yield depends on the overlap used and the manufacturer. For the worked example here, 13 pieces per m² is used as a planning value, counting pan and cover together, so confirm the figure on the manufacturer's data sheet. For a 50 m² roof plane, that is 650 pieces, plus a 10% wastage allowance (65 pieces), for a total of 715 pieces. Pan-and-cover tiles need a steeper pitch than Marseille-type profiles to drain properly between pan and cover, so check the manufacturer's minimum before choosing them.
What is the difference between Marseille and pan-and-cover tiles?
Marseille tiles are single pieces with a mechanical interlock, which makes them quicker and easier to lay, and they are the more common choice for new homes. Pan-and-cover tiles are two pieces, a channel (pan) and a cover, which take longer to lay but give a traditional curved look. They are common in restorations of older homes and need a steeper pitch than Marseille-type profiles. Compare quotes for each profile, since laying time and labour differ between them.
Should I use the plan area or the sloping area of the roof?
Always the sloping area, which is the real surface of the roof. The plan area is always smaller. To convert, use: sloping area = plan area × √(1 + (pitch % / 100)²). At a 30% pitch the factor is 1.044; at 45% it is 1.097. Using the plan area leads to buying fewer tiles than you need, with the risk of running short at the end of the job.
Is there a minimum roof pitch for each tile type?
Yes, and it depends on the profile and the manufacturer, so take the minimum from the technical data sheet for the exact product. As a general rule, pan-and-cover tiles need a steeper pitch than Marseille-type profiles, because water has to drain properly between the channel and the cover. Plain tiles have more joints, so their laying and minimum pitch also need care. Check the requirement with your council or building surveyor, since wind and rainfall in your area can call for a steeper pitch than the minimum on the data sheet.
When should I hire a roofing professional?
For any full re-roof or new roof, use a licensed roof tiler or builder. The tile count is a budgeting step and does not replace the roof design. A professional checks the roof framing (battens, rafters or trusses), the minimum pitch for the chosen profile, the underlay or sarking, and the flashings at ridges, valleys and eaves. On older homes, or homes in heritage areas, inspect the existing framing before starting, since it may need repair before new tiles go on.
Related calculators
By RivoCalc · Reviewed under our editorial methodology · Updated 3 June 2026
The results are estimates based on typical tile yields and the roof area you enter. Actual quantities depend on the manufacturer's data sheet, the roof shape, the laying method and local building requirements. Check the figures with your roofer or building surveyor before ordering.
