Brick Calculator: Bricks per Square Metre
Works out how many clay bricks a wall needs, with the mortar joint and a waste margin included. Optional material cost estimate.
A 10 m² wall (4 m long and 2.5 m high) built with clay bricks of 190 × 57 mm face, a 10 mm mortar joint and a 10% waste margin needs 821 bricks. Before waste, that is about 74.6 bricks per square metre of wall, or 82.1 once the margin is added.
The mortar joint is what makes this figure exact. Each brick occupies its face plus one joint in each direction, so it covers 0.0134 m² of wall rather than the 0.01083 m² of the brick face alone. Counting the bare face would overstate the total by about 24%, which in this example means around 195 bricks too many. The calculator adds the joint to both dimensions, divides the wall area by the area one brick covers, and rounds up.
Enter the wall length and height, the brick face dimensions, the joint thickness and the waste margin. Measure the wall as one rectangle, from the finished outline. The margin covers cuts at corners, openings for windows and doors, in-wall electrical boxes and bricks lost in handling. Use 5% for a simple rectangular wall and 10% for a wall with many openings or cuts. The result is the total number of bricks, and an optional price per brick turns it into a material cost estimate.
The same arithmetic applies to an interior partition, a garden wall, the infill above an opening or a brick veneer on a frame. The inputs stay the same, but what the wall has to do does not. Interior partitions and simple garden walls are straightforward. Load-bearing walls, retaining walls and brick veneer with its ties need a professional engineer or architect licensed in your province, and the local building permit rules always apply. This is a quantity tool, not a structural design tool.
The result updates automatically.
Typical ceiling height: 2.5–2.7 m (flat); up to 3.0 m (house) (about 8.2–8.9 ft; 9.8 ft).
Standard hollow brick: 30 cm · Acoustic brick: 37 cm (about 11.8 and 14.6 in)
Standard hollow brick: 20 cm · Thermal brick: 19 cm (about 7.9 and 7.5 in)
Typical on-site value: 1 cm (about 3/8 in)
Plain wall: 5% · With cut-outs and openings: 10%
Bricks needed
for a wall of 13.5
- Wall area
- 13.50 m²
- Bricks per unit area
- 15.4 unid./m²
- Effective area per brick
- 651 cm²
How it works
Formula
How the calculation works
How many bricks does a wall need?
Most new interior partitions in Canadian homes are framed with lumber or steel studs and finished with drywall, so brick is more often found in exterior walls, fireplaces, garden walls and repairs to older masonry. Whatever the wall, the quantity question is the same: how many bricks cover the wall area, including the mortar between them, plus a margin for waste on the job. This calculator answers that question for a single-thickness wall of clay brick, and it gives a total rounded up to a whole brick.
The formula and what goes into it
The calculator uses N = ⌈(A × (1 + D/100)) / ((L + J) × (H + J))⌉, where N is the number of bricks, A is the wall area in square metres, D is the waste margin in percent, L and H are the brick face length and height, and J is the mortar joint thickness. The ceiling brackets mean the result is rounded up to the next whole brick, so the wall always receives enough material.
The joint enters the formula twice because each brick is laid with mortar on its bed face, the horizontal joint below it, and on its head, the vertical joint at its end. Each brick therefore occupies a rectangle of (L + J) by (H + J), not just its face. For a brick face of 0.19 m by 0.057 m with a 0.01 m joint, that rectangle is 0.20 m by 0.067 m, or 0.0134 m².
Take a 4 m by 2.5 m wall, which is 10 m². Without waste, 10 ÷ 0.0134 = 746.3, so 747 bricks. With a 10% margin the area becomes 11 m² and the count becomes 821 (820.9, rounded up). The margin is applied to the area before dividing, so the same percentage applies to the count before rounding.
A larger wall shows the same pattern. A 5 m by 2.7 m wall, 13.5 m², needs 1,008 bricks with no waste. With a 5% margin the area becomes 14.175 m² and the count becomes 1,058 bricks.
Brick sizes and wall thickness
The calculator uses the face of the brick, the side you see on the wall. The worked examples on this page use a face of 0.19 m by 0.057 m (7 1/2 by 2 1/4 in). That is an example, not a standard size: enter the face dimensions printed on the data sheet of the brick you buy. The depth of the brick sets the thickness of the wall, but it does not change how many bricks cover a square metre of face. A single-thickness wall of the same face size takes the same number of bricks whatever its depth.
If the wall is built in two leaves, such as an outer brick leaf and an inner brick leaf separated by an air space, calculate each leaf separately, using its own area and brick size. The bricks in each leaf are separate units, so they must be counted separately.
Some catalogues give a nominal size that already includes the mortar joint, while others give the actual face size. Check which one the data sheet uses before you enter the numbers. Entering a nominal size and then adding the joint counts the joint twice and gives too few bricks.
Sizes differ between manufacturers, so the data sheet for the product you buy is the reliable reference. The masonry requirements of the building code and the project drawings define what your wall needs.
Mortar joint thickness
The joint is the layer of mortar between bricks, both the horizontal bed joints and the vertical head joints. A 10 mm joint is the value used in the worked examples on this page. The European reference standard EN 771-1 sets requirements for clay masonry units, such as their dimensions and strength, but it does not fix the joint thickness. That is set by the design and by workmanship practice, which is why the calculator asks for it as an input.
Joint thickness has real effects. A joint that is too thick uses more mortar, gives fewer courses per metre of height and reduces the strength of the masonry. A joint that is too thin is hard to lay evenly and may not fully bed the brick. Use the thickness in the project drawings or specification, and do not change it to make the count look better.
Choosing a waste margin
Waste comes from several sources: cuts at corners and wall ends, openings for windows and doors, sills and lintels, in-wall electrical boxes, bricks damaged in delivery or handling, and mistakes. Simple rectangular walls with few openings generally need a small margin, about 5%. Walls with several openings, many cuts or electrical boxes, or many bricks cut to fit against a column or an existing wall need a larger margin, about 10%.
Colour and size can vary between production batches, so buy the full order at once from one batch where possible. For a repair some years later, keep a few spare bricks from the same batch, because a replacement from a later batch may not match.
When this calculator is enough
The calculator suits non-load-bearing masonry: interior partitions, infill between existing framing, garden walls that are not retaining walls, and simple features. For these walls the inputs are geometry and the output is a material count, and the result does not depend on structural performance. A garden wall still has to meet local height limits and fencing bylaws, which you confirm with the municipality rather than with a calculator.
When to consult an engineer
Load-bearing walls, retaining walls, brick veneer with its wall ties, and any wall that forms part of a building permit application need design by a professional engineer or architect licensed in your province. The National Building Code of Canada 2020 is a model code. Each province and territory adopts and amends it, through instruments such as the Ontario Building Code or the Construction Code of Quebec, and some municipalities add their own requirements. The code in force where you build is the one that applies, so the local building department has the final word.
Seismic design applies in parts of Canada, notably coastal British Columbia, where seismic provisions add design requirements to masonry. Masonry design standards such as CSA S304 govern how the structure is designed, and no online calculator replaces that work.
Common mistakes
Five mistakes come up repeatedly.
The first is entering the nominal brick size and then adding the joint. This counts the joint twice and gives too few bricks, which means running short before the wall is finished.
The second is using the bare brick face and ignoring the joint. This overstates the count. In the 10 m² example it adds about 24% more bricks, which means buying more than the wall needs. Overbuying is less harmful than running short, but it still costs money and takes storage space.
The third is forgetting the waste margin. Real walls are rarely exact multiples of the brick size, so an exact count leaves no room for cuts or breakage.
The fourth is treating a two-leaf wall as one wall. Each leaf needs its own area and its own brick size.
The fifth is reading the material estimate as the full budget. The calculator prices bricks only. It does not include mortar, wall ties, lintels, sills, sealant, delivery, labour or any taxes.
Estimating the cost
The optional price field multiplies the number of bricks by the price per brick you enter. Use a current quote from a local supplier rather than a catalogue figure, because prices change with the season, the order size and the region. The estimate covers the bricks only, so the total cost of the job needs a separate estimate that includes the other materials and labour.
Before you order
Measure the wall as one rectangle, from its finished outline. The calculator does not subtract openings, so subtract large windows and doors by hand or leave them to the waste margin. Enter the actual face size from the data sheet, and take the joint thickness from the drawings. Order the full quantity from one batch, with the total rounded up as the calculator shows. If the wall is part of a permit application, ask the designer to check the quantity against the plans.
Frequently asked questions
How many bricks do I need per square metre of wall?
With clay bricks of about 190 × 57 mm and a 10 mm mortar joint, each brick covers 0.0134 m² of wall, so a square metre takes about 74.6 bricks before any waste. A 5% waste margin brings this to about 78.4 bricks per square metre, and a 10% margin to about 82.1. These figures apply to a single-thickness wall with a face of this size. Enter your own wall and brick dimensions in the calculator for the exact total, because the answer changes with the brick size and the joint.
How do I find the right brick size for my wall?
Use the face dimensions printed on the data sheet of the brick you buy, not a generic figure. The worked examples on this page use a clay brick face of about 190 × 57 mm (7 1/2 × 2 1/4 in) with a 10 mm joint. The depth of the brick sets the wall thickness, while the face size sets the number of bricks per square metre. Check whether the data sheet gives a face size or a nominal size that includes the joint. The building code that applies where you build sets the masonry requirements for the wall.
What waste margin should I use for bricks?
Use 5% for a simple rectangular wall with few openings. Use a higher margin, such as 10%, for walls with several window or door openings, many in-wall electrical boxes or corners, or where bricks must be cut with an angle grinder. Older buildings with irregular openings often justify an even larger margin. It is also sensible to keep a few spare bricks from the same batch, because colour and size can vary between batches and a later repair may need a match.
What is the mortar joint and what thickness should I use?
The mortar joint is the layer of mortar between bricks, both the horizontal bed joints and the vertical head joints. A 10 mm joint is the value used in the worked examples on this page. The thickness is set by the design and by the mason's practice rather than by the brick standard. Thinner joints need more precise laying, while thicker joints reduce strength and use more mortar. Follow the project drawings or specification.
What is the difference between solid and hollow bricks?
Solid bricks have no cores, so they are heavier and generally stronger in compression. Cored clay units have holes that reduce their weight. The calculator counts bricks from their face area, so the cores do not change the count, but the face size and the choice of solid or cored units must match the specification. Check the data sheet, and ask the designer which type the wall requires.
When should I consult an engineer for a brick wall?
Consult a professional engineer or architect licensed in your province for any wall that carries loads, any retaining wall, brick veneer with its ties, and any wall that forms part of a permit application. Parts of Canada, notably coastal British Columbia, have seismic design requirements that apply to masonry under the National Building Code of Canada, a model code adopted by each province and territory. Interior partitions and simple garden walls within local height limits are usually within the scope of this calculator, but the local building department has the final say.
Related calculators
Sand and Cement Calculator for Mortar
Calculates the cement bags and sand volume for mortar from the area, layer thickness and mix ratio.
Cement Bags for Concrete Calculator
Works out the cement bags needed for a slab, footing or wall from its volume, mix ratio and bag weight, with a 5% allowance.
Construction Cost per m² Calculator
Estimate the total cost of a construction or renovation project from floor area, cost per m² and regional factor, for projects in Canada.
View all Measurements & Quantities calculators →
By RivoCalc · Reviewed under our editorial methodology · Updated June 4, 2026
This calculator estimates the number of bricks for a wall. It does not provide a structural design. Results do not cover breakage beyond the waste margin, or the quantities of mortar, wall ties and accessories. Load-bearing walls, retaining walls and brick veneer with its ties need design by a professional engineer or architect licensed in your province. Check local building permit requirements before you order materials.
