Sand and Cement Calculator for Mortar
Calculates the cement bags and sand volume for mortar from the area, layer thickness and mix ratio.
For a 15 m² interior wall plastered 1.5 cm thick at a 1:4 mix, you need 4 bags of 25 kg cement and about 0.2 m³ of sand, with the 10 percent allowance for site losses included. This covers a typical room in a detached house or townhouse, where plaster goes on in two coats. For a 5 cm floor screed over the same 15 m², the requirement rises to 11 bags and about 0.66 m³ of sand. Thickness sets the volume directly, and the materials scale with it.
The mix ratio sets the strength of the mortar and is the one input that changes the quantities dramatically. A 1:4 mix (one part cement to four parts sand, by volume) is the common choice for interior plaster and general block or brick laying. A 1:3 mix is stronger and suits exterior stucco, foundations and areas in frequent contact with moisture. CSA A179 covers mortar for unit masonry in Canada, and the National Building Code of Canada 2020 is the model code that provinces and territories adopt. For a load-bearing wall or a permitted project, follow the mortar type specified by the designer rather than a general rule.
Enter the area, the layer thickness, the mix ratio and the bag weight. The calculator returns the number of cement bags, rounded up to a whole bag, and the matching volume of sand. If you enter current prices for cement and sand, it also estimates the material cost.
Use the result for your materials list, then confirm the quantity on site. Waste, uneven walls and first-time work all change real consumption, so it is worth keeping a spare bag on hand for the finish coat.
The result updates automatically.
1 cm bedding · 1.5–2 cm render · 4–7 cm screed
A standard bag of cement typically weighs 25 kg.
Bags of cement
for 0.150 m³ of mortar (10% allowance included)
- Mortar volume
- 0.150 m³
- Sand needed
- 0.16 m³
- Safety margin
- 10% included
How it works
Formula
How the calculation works
How to calculate sand and cement for mortar
Mortar is the material that bonds, levels and protects. It holds together brick and block, covers a wall with plaster or stucco, and forms a sand-and-cement screed under a floor. Many small jobs mix mortar on site from cement, sand and water in set proportions. Working out the quantity before you buy avoids two frustrating outcomes: leftover cement, which absorbs moisture and loses strength in storage, or running short halfway through a wall or a pour.
What the mix ratio changes in practice
The mix ratio is the proportion of cement to sand, expressed as parts by volume. Site mixing is normally done by volume, using buckets, shovels or a measuring box, rather than by weight. The four ratios you will see most often are:
- 1:3 (one part cement, three parts sand): the strongest common mix. Used for exterior stucco, foundations and areas exposed to moisture.
- 1:4 (one part cement, four parts sand): the most versatile. Used for block and brick laying, interior plaster and light sand-and-cement screeds.
- 1:5 (one part cement, five parts sand): a leaner mix for interior plaster in rooms with no special strength requirement.
- 1:6 (one part cement, six parts sand): for fill, levelling and low-stress work.
The mix ratio drives the strength of the finished mortar, which is why the calculator treats it as the main input that changes the quantities. The European standards EN 998-1 (rendering and plastering mortars) and EN 998-2 (masonry mortars) set the equivalent specifications in Europe. In Canada, CSA A179 covers mortar and grout for unit masonry. For a wall that carries load, or for work that is part of a permitted project, the mortar type shown on the drawings or specified by the engineer governs, not a rule of thumb.
How to calculate the volume of mortar
The base of the calculation is the volume of the layer: area multiplied by thickness. A 15 m² floor with a 5 cm screed needs 15 × 0.05 = 0.75 m³ of mortar before allowances. A wall measuring 3 m by 2.5 m has an area of 7.5 m². At 1.5 cm of plaster, the volume is 7.5 × 0.015 = 0.11 m³.
Typical thicknesses by type of work:
- Brick or block joints: 1 cm, both horizontal and vertical.
- Interior plaster (base coat plus finish coat): 1.5 to 2 cm in total.
- Exterior stucco: 2 to 3 cm, applied in two coats (scratch coat, then finish coat).
- Floor screed: 4 to 7 cm.
This calculator adds a 10 percent allowance to the calculated volume. Layer thickness is never perfectly even, corners are irregular, and some mortar drops during application. The allowance covers most ordinary jobs. Rough masonry, uneven substrates and first-time work usually call for more, so consider a few extra bags if you are working from a rough surface.
Cement, sand and where to buy them
Cement for mortar is normally general-use Portland cement, labelled Type GU, the general-use designation in CSA A3001. Masonry cement is also sold for mortar work. Check the bag label and confirm that the product suits the job.
Sand for mortar comes in two common types:
- Washed natural sand: the most common choice for plaster and mortar. Fine to medium grain, with few fines.
- Crushed sand: angular particles that bond well, often preferred for exterior stucco.
Sand is sold loose by the cubic metre from local aggregate suppliers, and bulk delivery is usually the cheaper option per unit of volume. For volumes above about 0.5 m³, bulk sand is nearly always the economical choice. For small repairs, pre-mixed dry mortar in bags avoids mixing, but it usually costs more per cubic metre than mixing on site. Enter your current prices in the calculator fields to estimate the cost of materials.
Common mistakes
Mixing volume and weight. Site mixes are by volume. Technical data sheets sometimes give mixes by weight, and the two bases are not interchangeable because cement and sand have different densities. Confirm which basis a data sheet uses before you follow it.
Using dirty sand. Clay and silt in sand, often called fines, increase the cement needed to reach the same strength. Sand taken directly from a pit often carries more fines than washed sand, so ask the supplier where it came from and whether it has been washed.
Adding too much water. A very wet mortar is easier to spread but loses strength. Use the least water that still gives a workable mix: it should hold its shape on the trowel and not slump off the board.
Skipping curing and cold-weather protection. Cement mortar needs moisture to gain strength. In hot, dry or windy weather, mist fresh plaster for the first two days to prevent cracking from fast drying. In cold weather, keep fresh mortar above freezing until it has set, because frost damages it.
Building codes and when not to use this calculator
The National Research Council of Canada (NRC) publishes the National Building Code of Canada 2020 (NBC), a model code that provinces and territories adopt and amend for their own use. The NBC is a model code, not federal law. Local building departments enforce the version adopted in their area, and some areas have additional requirements, so check with your municipality before starting work.
This calculator is not suitable for load-bearing masonry, structural repairs, or exterior work that requires a permit. In those cases, the specification from a licensed engineer or architect governs. Interior plaster and simple partition work is where the calculator is most useful.
Reading the result
The calculator rounds the cement bags up to the next whole bag, so a result of 3.17 bags becomes 4. The spare fraction is not wasted if you keep unopened bags sealed, dry and off the floor, because cement stored that way keeps well. Sand is given as a loose volume, so order it as loose volume too, and allow for the fact that damp sand takes up more space than dry sand.
Frequently asked questions
How many cement bags do I need to plaster 10 m²?
For 10 m² at 1.5 cm thickness and a 1:4 mix, the volume is 0.15 m³. With the 10 percent allowance, that becomes about 0.165 m³ of mortar. At about 320 kg of cement per m³ for a 1:4 mix, you need roughly 53 kg of cement, which is 3 bags of 25 kg after rounding up. The sand required is about 0.13 m³.
What mix ratio should I use for brick or block laying?
For interior block and brick laying in dry locations, a 1:4 mix (one part cement to four parts sand, by volume) is the common choice. For exterior walls or areas exposed to moisture, use 1:3 for more strength. Joint thickness is set by the masonry unit specification and the designer's drawings, so check the block or brick data sheet before you start. For a load-bearing wall, confirm the mortar type with the designer, since a general rule cannot replace the specification.
What is the difference between mortar and concrete?
Mortar is a mixture of cement, sand and water, with no coarse aggregate. It is used for plaster, brick and block joints and screeds. Concrete includes coarse aggregate, usually gravel or crushed stone, and has higher compressive strength, which makes it suitable for structural elements such as slabs, columns and footings. In practical terms, mortar is for finishing and masonry, and concrete is for structure.
When should I use a 1:3 mix instead of 1:4?
Use a 1:3 mix where the mortar needs more strength or resistance to water: exterior stucco exposed to rain and freeze-thaw cycles, walls in areas that get regular splashing or dampness, and garden walls or foundations in contact with the ground. A 1:4 mix suits most interior plaster and masonry in dry locations. For structural walls, the designer's specification governs.
Is pre-mixed dry mortar in bags worth it instead of mixing on site?
Pre-mixed dry mortar in bags suits small repairs, where no mixer is available or you need a factory-controlled mix. It usually costs more per cubic metre than mixing cement and sand on site, so for jobs of about 0.2 m³ or more, calculating and mixing on site is usually more economical. Compare current prices from local suppliers, and read the product data sheet for the mixing water and the working time.
What is the correct plaster thickness?
There is no single correct figure, because the right thickness depends on the surface, the finish and the product used. Interior plaster is normally applied in two coats, a base coat and a thinner finish coat, and the maximum layer thickness is set by the manufacturer's data sheet. Thick single coats raise the risk of shrinkage cracking. For exterior stucco or thick coats, the data sheet also states whether mesh reinforcement is required. The thickness ranges in the how-to steps are planning estimates only.
When should I hire a professional for mortar work?
For simple interior plaster or partition block, this calculator is enough. For exterior stucco on buildings, work near persistent water leaks, repairs to walls with rising damp, and any work that needs a building permit, consult a licensed engineer or architect. Permitted alterations may require drawings signed by a qualified professional. Provincial associations for engineers and architects publish searchable registers of licensed members, which you can use to check credentials.
Related calculators
Brick Calculator: Bricks per Square Metre
Works out how many clay bricks a wall needs, with the mortar joint and a waste margin included. Optional material cost estimate.
Cement Bags for Concrete Calculator
Works out the cement bags needed for a slab, footing or wall from its volume, mix ratio and bag weight, with a 5% allowance.
View all Structure & Materials calculators →
By RivoCalc · Reviewed under our editorial methodology · Updated June 3, 2026
This calculator gives estimates of material quantities for planning purposes only. Real consumption depends on the surface, the skill of the applicator, waste and weather. It does not replace the design of a licensed engineer or architect, and it does not cover load-bearing or structural work. Check local building code and permit requirements with your municipality before starting.
