Skip to main content

Entry Door Cost Calculator for Canadian Homes

Estimates the cost of a new or replacement entry door, from a standard wood or aluminum unit to an RC2 or RC3 security door, with optional installation and removal.

A door certified to EN 1627 class RC2 resists at least 3 minutes of forced entry with hand tools such as a pry bar and a screwdriver. For a standard 914 x 2032 mm (36 x 80 in) entry door, the total is the door unit, plus installation, plus removal of the old door when needed. The figure depends mainly on three choices: the door type, its certification level and whether a qualified installer fits it.

Two houses can buy the same door unit and still pay different amounts, for example a bungalow in Ottawa and a townhouse in Calgary, because the frame, the condition of the opening and the access change the labour. The frame has to be shimmed, fixed to the framing and sealed, so that the door keeps its rated performance and does not leak air or water. An older house may also need the rough opening adjusted, and that work is not something the calculator can predict, so treat the result as a starting point.

Entry doors sold in Canada range from solid wood and insulated steel to fibreglass, aluminum and composite units. Security doors rated RC2 are usually steel-clad with a multi-point locking system and reinforced hinges. RC3 doors add a thicker steel plate and high-security cylinders, which suits homes in higher-risk areas or homes with valuables. A detached house in Toronto or a semi-detached in Halifax usually starts the comparison at RC2, because that level balances protection and cost.

Each option needs a different amount of installation work. A certified security door keeps its rating only if the complete assembly is installed as tested, including the frame, lock and hinges. A rated leaf hung in a weak frame behaves much like a standard door under attack, so the installer matters as much as the product.

Use the calculator to set a realistic budget before asking for quotes. Choose the door type, select installation if a professional will fit it, and add removal if an existing door must come out. Then compare the total with at least two or three written quotes that list the door model, its certification, the frame type, the fixing method and the lock details.

The explanation below uses metric units; the calculator works in either system.

The result updates automatically.

Reference costs for entry doors in Canada depend on the door type, the certification level, the frame and the scope of installation. They vary with local labour rates, supply and the condition of the opening. Enter the figure from your own written quote to refine the estimate. Exterior doors are specified for cold winters and wind-driven rain, so check thermal performance and weatherstripping against the National Building Code of Canada as adopted in your province or territory.

Fitting the frame, hanging the leaf, adjusting the ironmongery and sealing around the edge.

Removing the existing frame and leaf, and taking them to the tip.

Estimated total cost

~$1,840.00

Estimate based on the prices entered.

Door + frame + ironmongery
$1,500.00
Installation
$225.00
Removal of the old door
$115.00
Estimated total
$1,840.00

Turn this calculation into a quote for your client

We're building a tool for professionals. Be among the first to try it.

Share

How it works

1

Choose the door type: solid wood, insulated steel, fibreglass, aluminum or composite, or a security door rated RC2 or RC3.

2

Select the installation option if a professional will fit the frame, hang the door and seal the perimeter.

3

Select the removal option only if an existing door has to come out of the opening.

Formula

C = Dp + Ins + Rem
C — estimated total cost
Dp — door cost (door leaf, frame and hardware)
Ins — installation cost, covering frame fitting, fixing and adjustment
Rem — removal cost of the old door, when applicable

How the calculation works

Entry door cost: from a standard door to an RC3 security door

A new entry door is one of the home improvements that most affects security, energy loss, noise and the look of the house. The total cost depends on the material, the certification level and whether a professional installs it. The calculator estimates the total from three separate parts, so you can see which decision moves the budget most. Enter your own parameters to get an estimate for the job you are planning.

What the calculator adds up

The formula is C = Dp + Ins + Rem. C is the estimated total cost. Dp is the cost of the door itself, meaning the leaf, the frame and the hardware such as hinges, lock and handle. Ins is the installation cost, which covers fitting the frame, fixing it to the wall structure, hanging the door and adjusting it. Rem is the cost of removing the old door, which applies only when you replace an existing unit.

Each part is independent. If you do not need removal, Rem is zero and the total is the door plus installation. If you install the door yourself, Ins is zero, but the work still needs the right fixings, sealing and adjustment, and a rated door installed badly loses its rating. The three parts are added directly, with no discount or multiplier, so each part can be checked separately against quotes.

Door types on the Canadian market

Several door families are common in Canadian homes.

Solid wood or wood-veneer doors are usually the lowest-cost option. They offer a traditional look and limited thermal performance. They have no security rating and are the easiest to force. Wood needs regular finishing, and its service life depends on exposure to rain, sun and freeze-thaw cycles, so the manufacturer's care instructions matter.

Insulated steel doors are the most common residential exterior door. The steel skin is paired with an insulating core, which improves thermal performance and resists dents. Steel doors are not automatically security doors, so check whether the product carries a forced-entry rating.

Fibreglass doors imitate wood grain, resist moisture and warp less than solid wood. They sit in the mid-range, with good thermal performance.

Aluminum or composite doors are light and resist corrosion. Aluminum is used more often in glazed or commercial designs than in solid security doors.

Security doors rated RC2 combine a reinforced steel leaf, a multi-point locking system and reinforced hinges with a frame designed to be fixed into the wall structure. An RC2 door is the usual choice when the aim is real forced-entry resistance at a reasonable cost. The protection only works when the full assembly is installed as tested.

Armoured doors rated RC3 or higher use a thicker steel plate, a heavier frame and high-security cylinders. They suit homes in higher-risk areas, isolated detached properties, or homes that store items of significant value. Installation is more demanding, and the cost difference compared with RC2 reflects the added materials and the specialist work.

The EN 1627 classes

The European standard EN 1627:2011 grades the forced-entry resistance of doors, windows, shutters and grilles across six classes, RC1 to RC6. The older designation was WK, so you may see WK2 or WK3 on product literature. Class RC1 offers basic manual resistance and is not enough for a main entry door. RC2 is tested against hand tools such as a pry bar and a screwdriver for at least 3 minutes. RC3 is tested for longer and against more demanding tools, including power tools.

Canadian buyers will mostly see this European standard in imported products. The National Building Code of Canada, published by the National Research Council of Canada, is a model code. Each province and territory adopts and amends it, so it is not federal law. It addresses structural, fire and egress requirements that can affect door size and location. Forced-entry ratings are usually quoted by the manufacturer against a named test standard, so ask which standard applies and request the test report from the supplier.

A rating applies to a tested assembly, meaning the leaf, frame, lock and hinges together. A door certified as a set does not perform the same if one component is replaced with a weaker one.

Installation and the frame

The frame, or jamb assembly, is often sold separately. Many buyers focus on the price of the leaf and forget that the frame is the link between the door and the wall. A strong leaf in a weak frame gives way at the strike plate, at the hinge side or at the fixing points.

In a wood-framed wall, a correct installation fixes the frame to the studs and header with suitable screws, shims the frame so it is plumb and square, and seals the perimeter against air and water. In a masonry wall, the frame needs anchors designed for masonry. The fixing method and the number of fixings should follow the manufacturer's instructions for the specific product.

Exterior doors also need a good weather seal and threshold. Cold air leakage raises heating costs and can cause condensation on the frame, so check that the threshold and sill details follow the product's installation instructions.

Removal of the old door

Removing an old door means taking off the leaf and the frame and disposing of the materials. An old frame may be fixed into a rough opening that has to be repaired before the new frame goes in. Framing around the opening can be damaged, for example by rot in a wood frame or by corrosion in a steel frame, and that repair adds to the total. If you suspect rot, check the sill and the framing before ordering the new door.

Edge cases

If the new door is the same size and fits the same opening, the adjustment work to the rough opening is minimal and the installation is simpler. A different size, a different swing direction or a different threshold height changes the frame work. A zero removal cost means no old door is taken out, for example in a new build or where the opening is already empty. A zero installation cost is only realistic when you do the work yourself or when the seller fits the door at no charge, which should be confirmed in writing.

Permits, codes and swing direction

Many municipalities require a permit for work that changes an exterior opening, alters structural framing or moves a door. Check with your municipal building department before ordering. The swing direction, whether the door opens in or out, the width of the exit path and the fire separation between a house and an attached garage can all be regulated. The National Building Code of Canada and the provincial codes address these matters, and local rules may be stricter.

When to use the calculator, and when not to

Use the calculator at the planning stage to compare door types, decide whether to include installation and set a budget range before quotes are requested. It is also useful for checking whether a quote includes removal and installation as separate lines.

Do not treat the result as a quote. The calculator does not know your local labour rates, site access, the condition of the rough opening or the exact product you will buy. Do not use it to decide whether a door meets a specific security or fire requirement. Those questions need the test report, the product's installation instructions and the advice of a qualified professional.

Common mistakes

Choosing a door by the price of the leaf and forgetting the frame, the lock or the installation is the most frequent error. A second mistake is buying a security door and keeping an old lock with weak forced-entry resistance, because the lock is the weakest point of many assemblies. A third is ordering the wrong size or swing direction, which forces a new frame or the return of the complete unit. A fourth is comparing quotes that do not describe the same specification, such as an unrated door set against a rated one. Ask every contractor to state the door model, the certification, the frame type, the fixing method, the lock and whether perimeter sealing is included.

Insurance and documentation

Some home insurance policies set conditions on doors, locks and security features. Check the policy wording before buying, and keep the invoice, the product data sheet and the installation details, because an insurer may ask for them when you make a claim. This is a practical step and not a guarantee of any change to your premium.

Sources and next steps

Use the calculator together with the EN 1627:2011 test report for the product, the National Building Code of Canada as adopted in your province or territory, and your municipal permit requirements. These are public normative sources. They set the performance and installation rules that a cost estimate cannot replace.

Frequently asked questions

What affects the cost of a new entry door in Canada?

The cost depends mainly on the door type (solid wood, insulated steel, fibreglass, aluminum or composite, or a security door rated RC2 or RC3), on whether installation is included, and on whether an old door has to be removed. The condition of the frame, the size of the opening and local labour rates also change the total. The calculator separates the door, installation and removal, so you can see which part of the budget drives the result. Use it to plan, then confirm the final figure with written quotes from contractors who list the exact door specification.

What does an RC2 or RC3 rating mean?

RC stands for resistance class. It comes from the European standard EN 1627, which grades how well a door assembly resists forced entry, from RC1 to RC6. An RC2 door is tested to resist a hand-tool attack for at least 3 minutes, a common target for a main entry door. RC3 is tested for longer and against more demanding tools. The rating applies to the whole assembly, including the leaf, frame, lock and hinges, so a rated door in a weak frame does not perform to its rating. Canadian products may also be tested to other programs, so ask the supplier for the test report.

Is installation included in the price of a door?

Usually not. Suppliers often sell the door unit separately from installation, and the frame is frequently a separate item. Professional installation normally covers removing the old frame, fitting and fixing the new one, hanging and adjusting the door, and sealing the perimeter. For rated security doors, professional installation is strongly recommended, because an incorrect frame or fixing can stop the door performing to its rating. In the calculator, select the installation option to add this cost to the estimate.

Which door type suits a house in Canada?

For most detached homes, an insulated steel door or a security door rated RC2 offers a practical balance of protection, weather performance and cost. A standard wood or aluminum door without a security rating is easier to force. An RC3 door is worth considering for a rural property, a home with a history of break-ins or a home that stores valuables. Check your insurer's policy wording before buying, because some policies set conditions on doors and locks. Choose a door with a good weather seal and a suitable thermal rating for your climate.

What is the difference between a security door and an armoured door?

Armoured door is a common, informal term for a door with a steel plate or steel-clad core and a high rating, often RC3 or higher. Security door is the general term for any door tested to a recognized standard, from RC1 upward. In the retail market the words are used loosely, so a door sold as armoured may only be RC2. Ask for the test report or the declaration of performance, and confirm the rating class and the standard it was tested against. The label alone does not tell you the protection level.

When should I consult a specialist instead of relying only on this calculator?

The calculator gives a planning estimate. Consult a qualified installer or contractor when the opening is non-standard, when the door must open outward, when the door connects to an attached garage that needs fire separation, or when the door is part of a home automation or video intercom system. Condominium buildings may also have rules on exterior doors. Check permit requirements with your municipal building department before work starts, and get at least two or three written quotes that describe the same specification.

Related calculators

View all Renovation & Systems calculators →

By RivoCalc · Reviewed under our editorial methodology · Updated July 15, 2026

This calculator gives an estimate for planning only. Real costs vary with the product, the region, labour rates, site access and the condition of the existing frame. Security and fire-rated doors must be installed to the manufacturer's instructions and to the National Building Code of Canada as adopted in your province or territory. Check permit requirements with your municipality before work starts.