Skip to main content

Pitched Roof Area Calculator

Calculates the true sloping area of a pitched roof from plan dimensions and pitch, for ordering tiles and other roofing materials.

A roof with 100 m² on plan and a 35% pitch has a true sloping surface of about 105.9 m², which is 5.9 m² more than the footprint suggests. Estimating from the plan area is the most common and most expensive mistake in roofing, because tiles, underlay and battens are bought for the surface that is actually covered.

This calculator converts the plan dimensions into the true sloping area using the trigonometric relationship that applies to any pitched roof. It works for a monopitch roof (a garage, porch, lean-to or side extension), a dual-pitch gable roof and a hip roof with four slopes. The base formula is the same in each case: sloping area = plan area × √(1 + (pitch%/100)²). A 20% pitch adds 2.0%, a 30% pitch adds 4.4% and a 45% pitch adds 9.7%.

Take a semi-detached house in a Dublin suburb with an 80 m² footprint and a 35% pitch. The roof surface is about 84.8 m², so a figure taken from the footprint would be 4.8 m² short before any allowance for waste. Enter the plan length and width, the pitch as a percentage, and the number of roof slopes. The calculator shows the total sloping area, the slope factor, the estimated ridge height and, optionally, the area with a waste allowance added.

Use the sloping area as the basis for quantities of tiles, underlay, battens, insulation, gutters and ridge tiles. Check each figure against the coverage stated on the manufacturer's data sheet, because coverage depends on the product and the lap used.

The result updates automatically.

Parallel to the ridge — eave to eave

Perpendicular to the ridge — eave to eave

30% means it rises 30 cm for every horizontal metre (3.6 in per foot). Typical values: 25 to 45%.

10% for simple roofs; 15% for multiple faces with valleys.

Total sloped area

83.5m²

4.4% more than the plan area of 80.0

Area with a 10% allowance

91.9m²

the quantity to use when ordering materials

Plan area
80.0 m²
Pitch factor
×1.0440
Ridge height
1.20 m
Increase over the plan area
+4.4%

Turn this calculation into a quote for your client

We're building a tool for professionals. Be among the first to try it.

Share

How it works

1

Measure the length and width of the roof on plan, from eaves to eaves in each direction.

2

Enter the pitch as a percentage. A 30% pitch means the roof rises 30 cm for every metre of horizontal run. If your figure is in degrees, convert it first: 20 degrees is about 36%.

3

Select the number of roof slopes. The sloping area is calculated with the same formula for every type.

Formula

A = C × L × √(1 + (p/100)²)
A — Actual sloping roof area (m²)
C — Plan length (m), parallel to the ridge
L — Plan width (m), perpendicular to the ridge
p — Pitch (%), metres of rise per 100 metres of horizontal run
√(1 + (p/100)²) — Plan-to-slope conversion factor (always 1 or more)

How the calculation works

How to calculate the real area of a pitched roof

The area of a roof is never the same as the area of the building on plan, and the difference grows with the pitch. At a 30% pitch the sloping surface is 4.4% larger than the plan area, and at 45% it is 9.7% larger. On a roof covering 100 m² on plan, that is 4.4 m² of extra surface at 30% and 9.7 m² at 45%. Every extra square metre needs covering, underlay and fixings, so an estimate based on the plan area will come up short.

The relationship follows from basic trigonometry. Take a right-angled triangle with a horizontal side of 100 units and a vertical side of p units, where p is the pitch in percent. The sloping side is the hypotenuse, √(100² + p²). Dividing the hypotenuse by the horizontal side gives the conversion factor, √(1 + (p/100)²). Multiplying the plan area by this factor gives the sloping area. At 30%, √1.09 is about 1.044. At 35%, √1.1225 is about 1.059. At 45%, √1.2025 is about 1.097.

Why one formula works for every roof shape

If every plane of a roof has the same pitch, the total sloping area is the plan area multiplied by the same factor, whatever the shape. Each plane is tilted at the same angle θ, so its surface area equals its plan area divided by cos θ. The plan areas of all the planes add up to the total plan area, so the sloping areas add up to the plan area divided by cos θ. Since 1 / cos θ = √(1 + tan²θ) and tan θ = p/100, the result matches the formula. This holds for a monopitch, a gable and a hip roof, because the hip ends slope at the same angle as the main planes.

Where planes have different pitches, for example a south slope set flatter for solar panels and a steeper north slope, apply the formula to each plane using its own plan area, and add the results. The calculator takes one pitch for the whole roof, so run it once for each part. At 0% the factor is exactly 1, so a flat roof has the same area as its plan.

Pitch: percentages, degrees and measurement

Pitch can be stated as a percentage or as an angle, and the two are not interchangeable. A percentage pitch is the vertical rise divided by the horizontal run, multiplied by 100. An angle is the arctangent of the same ratio. A 30% pitch is an angle of 16.7 degrees, and a 30 degree angle is a pitch of 57.7%. Many roofing specifications and manufacturers' data sheets give pitch in degrees, while some design drawings use percentages. Confirm the unit before entering a value. Typical conversions are:

  • 20%: 11.3 degrees
  • 30%: 16.7 degrees
  • 35%: 19.3 degrees
  • 45%: 24.2 degrees

Each covering has a minimum pitch in the manufacturer's technical data sheet, which is the reference for that product. A pitch that is too low slows the run-off of water and lets wind-driven rain find its way under the laps, so lap and verge detailing matters on exposed sites at any pitch.

To measure the pitch of an existing roof without instruments, use a spirit level about 30 cm long. Place it flat on the roof surface, lift one end until the bubble is central, and measure the height of the raised end above the surface. Divide that height by 30 and multiply by 100. A raised end 10 cm high gives a pitch of 33%. Work on a roof only with appropriate fall protection, and where possible take measurements from the ground or from a safe access point.

Roof types

Monopitch (lean-to). A single slope with a higher and a lower eave. It is common on garages, porches, outbuildings and side extensions. The height difference between the eaves is the width multiplied by the pitch. For a 4 m wide lean-to at 25%, the eaves differ by 1.0 m. The sloping area is still the plan area multiplied by the factor.

Dual pitch (gable). Two symmetrical planes meet at the ridge. The ridge height above the eaves is half the width multiplied by the pitch. For an 8 m wide house at 35%, the ridge sits 1.4 m above the eaves. The gable walls are vertical walls rather than roof planes, so they are not included in the roof area.

Hip roof (four slopes). Four planes meet at a ridge shorter than the building. The ridge height is set by the shorter plan side: half of that side multiplied by the pitch. For a plan of 10 m by 8 m at 35%, the ridge height is 4 × 0.35 = 1.4 m and the ridge length is 10 m minus 8 m, which is 2 m. Hips and valleys produce more cut tiles than a gable, so the waste allowance should be higher.

Common mistakes

Using the plan area as the roof area. At a 30% pitch, 80 m² on plan becomes 83.5 m² of roof. Ordering for 80 m² leaves 3.5 m² uncovered before any waste is added. The shortfall is often found halfway through the job, when extra material may come from a different batch and the colour may not match.

Confusing percentage with degrees. A 30% pitch is not a 30 degree angle. Check the unit on every drawing and data sheet, and convert before using the calculator.

Applying the factor to measured lengths. If you measure each plane along its surface, multiply those lengths by the plane's width without applying the factor again. The factor is only for plan dimensions.

Waste allowance

The waste allowance covers cut tiles at verges, hips, valleys and abutments, breakages during handling and fixing, and the end laps at the ends of each run. A simple gable with few cuts needs a smaller allowance than a roof with many valleys, hips and dormers. Coverage per tile is set by the manufacturer, so check the allowance against the data sheet for the product you choose.

Standards and when to get a professional

The European standard EN 1304 covers clay roofing tiles and fittings. The area calculation is a step in budgeting and in checking contractors' quotes, and it does not replace a roof design. For full replacement or new construction, a competent professional should check the roof structure, including rafters, purlins and wall plates, the suitability of the pitch for the chosen covering, the underlay, and the detailing at ridges, valleys, eaves and verges. The works must also meet the Building Regulations, including Part A (structure), Part C (moisture) and Part L (energy), as set out in the Technical Guidance Documents.

For older buildings, have the timber structure inspected for rot, fungal decay and wood-boring insects before any re-roofing. Before ordering materials, ask the local planning authority whether the works need consent.

Frequently asked questions

How do I convert the plan area to the sloping roof area?

Multiply the plan area by the factor √(1 + (pitch/100)²). At a 30% pitch the factor is √1.09, or about 1.044, so the sloping area is 4.4% larger than the plan area. At 45% the factor is about 1.097, or 9.7% more. Example: a roof with 80 m² on plan at a 35% pitch has a sloping area of 80 × √1.1225 ≈ 80 × 1.059 ≈ 84.8 m², which is 4.8 m² more. Use the sloping area for all material quantities, and add a waste allowance on top of it.

What is the difference between pitch as a percentage and pitch as an angle?

Pitch as a percentage is the vertical rise divided by the horizontal run, multiplied by 100. Pitch as an angle is measured in degrees. The two are not interchangeable: a 30% pitch is about 16.7 degrees, and a 30 degree angle is about 57.7%. Irish and UK trade documents often use degrees, so confirm the unit before entering a value. This calculator takes a percentage. To convert degrees to a percentage, take the tangent of the angle and multiply by 100. For example, 20 degrees is about 36.4%.

By how much does a 30% pitch increase the roof area?

At a 30% pitch the sloping area is 4.4% larger than the plan area. For a roof with 100 m² on plan, the sloping area is about 104.4 m². At 20% the increase is 2.0%, giving about 102.0 m². At 45% it is 9.7%, giving about 109.7 m². The increase does not grow in a straight line with the pitch, because the factor follows a square-root curve, so the gap widens more quickly at steeper pitches.

Does the formula work for a hip roof with four slopes?

Yes. For any roof where every plane has the same pitch, whether it has one, two or four slopes, the total sloping area equals the plan area multiplied by the same factor. Each plane is inclined at the same angle, so its surface area is its plan area divided by the cosine of that angle, and the plan areas of all the planes add up to the total. The formula only needs adjusting when the slopes have different pitches. In that case, calculate each slope separately and add the results.

What is the sloping area used for?

The sloping area is the basis for estimating quantities of roof covering, including tiles, slates, underlay or breathable membrane, battens and insulation. It is also used to estimate the cost of re-roofing. Using the plan area for these estimates usually results in too little material, which can force an urgent second order part way through the job, with a risk that the replacement tiles come from a different batch. Add a waste allowance for cuts and breakages. The roof tile quantity calculator on this site takes the sloping area as its input.

When should I hire a roofing professional?

For a full replacement or a new roof, the sloping area is only one step in the estimate. A competent professional should check the roof structure, including rafters, purlins and wall plates, the suitability of the pitch for the chosen covering, the underlay, and the detailing at ridges, valleys, eaves and verges. Older buildings should have the timber inspected for rot, fungal decay and wood-boring insects before re-roofing. Before ordering, check with the local planning authority whether the works need consent, particularly for protected structures or buildings in a conservation area.

Related calculators

By RivoCalc · Reviewed under our editorial methodology · Updated 12 May 2026

This calculator estimates roof surface area for ordering materials. Results depend on the accuracy of the measurements entered. It does not assess the structure, weather resistance or compliance with the Building Regulations, which need a qualified professional.