Fence Cost Calculator per Metre
Estimates the total cost of a garden fence per metre for wire mesh, removable steel panels, timber or precast concrete, including labour.
For a back yard measuring 10 m by 8 m in Hamilton, the fence has to enclose 36 m of boundary. With 1.2 m galvanised steel mesh and a post every 2.5 m, that run needs 16 posts: 36 divided by 2.5 is 14.4, which rounds up to 15 spans, plus one post to close the run.
The total cost is the run length multiplied by the combined material and labour rate per metre. The calculator does not price posts on their own, so include the cost of posts, concrete footings and ground preparation in the material or labour rate you enter. The rates are the part of the calculation that changes most between regions and suppliers, so they deserve the most care. The post count tells you how many posts to order and set out.
Enter the total length in metres, choose a fence type, and add the material and labour rates from your quotes. If you set labour to zero, the result shows the material cost only, which helps when you are comparing supplier prices on their own. The estimate is only as good as the rates you enter.
The four common options are welded or hexagonal wire mesh, removable steel panels, timber, and precast concrete walls. Mesh is usually the lowest cost per metre and needs little upkeep once tensioned. Removable panels cost more but look neat and last with light maintenance. Timber sits in the middle and needs regular treatment or oiling. Precast concrete gives full privacy and the least upkeep, but it has the highest up-front cost.
Before you order, check two things. Your council's district plan sets limits on fence height and placement, and a boundary fence affects your neighbour, so read the [Fencing Act 1978](https://legislation.govt.nz/act/public/1978/50/en/latest/) before you start. Neighbours can cause more delay than the build itself, so raise the plan with them early.
The result updates automatically.
Add up all the sections. For a 10 m × 8 m garden, the perimeter is 36 m.
This automatically updates the reference prices. Adjust to match the quote you've received.
Reference value for this type of fencing. Adjust to match the quote you've received.
Enter 0 to see the material cost only.
Estimated total cost
For 40 of fencing
Material cost
40 × $10.00 per unit length
Labour cost
40 × $10.00 per unit length
- Total length
- 40
- Estimated posts (every 2.5 m / 8.2 ft)
- 17
- Material cost
- $400.00
- Labour cost
- $400.00
- Total cost
- $800.00
How it works
Formula
How the calculation works
Fence cost in New Zealand: how to work out the figure
A new fence marks the edge of a property, changes how a section looks from the street and gives privacy and some security. The cost per metre varies a great deal between fence types, from welded wire mesh, which is usually the cheapest, to precast concrete walls, which cost the most at the start but need the least upkeep. Anyone who asks for quotes without a rough idea of those price relationships is at a disadvantage when the figures arrive, so it helps to know which type suits the site before you start.
The type you choose reflects durability, upkeep and installation cost over many years, not only appearance. A cheap fence that needs repainting or re-tensioning every few years can cost more over its life than a dearer fence that needs almost nothing. That is why the calculator asks for material and labour separately: you can compare the two parts of each quote on equal terms.
The calculation itself is simple. Multiply the total length of boundary to be fenced by the combined material and labour cost per metre. The calculator also gives the number of posts, which tells you how much timber, steel or concrete to order and how many holes to dig.
How the formula works
The total cost is C_total = L × (p_m + p_lab). L is the length of fence, p_m is the material cost per metre and p_lab is the labour cost per metre. The two rates are added before being multiplied by length, so a change of one unit in either rate moves the total by L units. That is a simple way to check how a price change in a quote affects the result.
The post count is a separate expression: N_posts = ⌈L / 2.5⌉ + 1. Dividing the length by the 2.5 m spacing gives the number of spans. Rounding up means a part-used span still needs a full post at its end, and the extra post closes the run. For 36 m, 36 ÷ 2.5 = 14.4, which rounds up to 15 spans, giving 16 posts. For 40 m, the same method gives 17 posts.
The post count does not feed into the cost. Each post, its concrete footing and any digging or ground work are part of the rate you enter. If your quote prices posts separately, divide that total by the length and add the result to the material or labour rate per metre, or the estimate will come out low.
Fence types and what drives their cost
Four types are covered. The table shows their general positions relative to each other. These are not fixed prices: the real figure depends on the supplier, the region, the height and the site.
| Fence type | Relative material cost | Relative installed cost | Upkeep |
|---|---|---|---|
| Welded or hexagonal wire mesh, 1 m | Lowest | Low | Very little once tensioned |
| Timber, 1 m | Low to medium | Medium | Regular treatment or oil |
| Removable steel panels, 1.5 m | Medium to high | High | Occasional touch-up of the coating |
| Precast concrete wall, 1 m | High | High | Very little for many years |
Wire mesh is the least expensive option per metre and is common on rural properties, lifestyle blocks and back boundaries. Hot-dip galvanised mesh comes in 1 m rolls. It needs round posts, typically galvanised steel tube around 40 mm in diameter, set at 2.5 m spacing, with the mesh tensioned along the top and bottom wires or fixed with clips. For a 40 m run in the outer suburbs of Tauranga, the material cost is the local rate per metre multiplied by 40, and the labour is added the same way.
Timber suits gardens with a relaxed or rural look. Treated pine and macrocarpa are both used. Use timber treated for ground contact for any posts set in the soil, and ask the supplier to confirm the treatment before you buy. Timber needs regular treatment with a suitable exterior oil, stain or varnish. That recurring cost and effort is something wire mesh and steel panels do not carry, so include it when you compare the total cost over the life of the fence.
Removable steel panels are a common choice for street frontages and driveways. They are made from electro-welded steel bar with an epoxy powder coating, usually around 1.5 m high. A well-coated panel fence lasts for many years with little maintenance, apart from occasional touch-ups where the coating is chipped. The total cost, with posts and labour, sits clearly above wire mesh or timber. Gates are not included in the per-metre rate and need their own quote.
Precast concrete walls give full privacy and a solid, long-lasting finish in smooth or textured panels, some imitating stone. They carry the highest up-front cost per metre, because the panels need posts, footings and a skilled installer. Their upkeep stays very low for many years. If the wall is taller than a standard fence, or if it holds back soil, get advice from an engineer or a Licensed Building Practitioner before you treat it as a simple fence.
Posts and spacing: the detail that sets the rigidity
For wire mesh and timber, post spacing decides how rigid the fence is and how it looks. The calculator assumes a fixed spacing of 2.5 m. This is a planning assumption that keeps the count simple, not a code requirement, and it suits 1 m mesh on level ground. Taller fences of 1.5 to 2 m, and fences on exposed sites, may call for closer spacing. The calculator does not adjust for this, so if your installer proposes closer spacing, count the extra posts by hand and price them separately.
Posts are usually set in concrete. Quick-set concrete speeds up the work and adds a small cost per post that is easy to forget. Include it in the rate.
Ground, slope and access
Uneven ground changes the job. A fence on a slope either steps down in sections or follows the fall, and both need more cutting, more posts or more time. Site preparation, such as setting out the line, clearing vegetation, digging post holes and levelling, is often charged separately from the fence. Narrow access, steep sections or limited room for a digger also raise the labour. Central city sites in Auckland or Wellington with restricted access often cost more to fence than open rural or outer suburban sites, which usually sit at the lower end of the local range. Use the labour rate from a quote for your actual site, not a general figure.
Rules that can limit height and placement
District plans set the height and placement of fences. They often allow lower heights at the road frontage than along side and rear boundaries, and some also limit solid fences near driveways for visibility. Rules vary by council and by zone, and heritage or special character areas can add conditions. Check the district plan before you buy materials.
Whether a fence needs building consent depends on its height, its structure and where it sits. Walls, retaining walls and fences with significant footings or structural parts may fall under the Building Act 2004, which sets out the performance requirements in the New Zealand Building Code. MBIE administers that Act and the Building Code. Ask your council whether consent is needed before you order. For restricted building work, the people to ask are Licensed Building Practitioners.
Boundary fences also involve your neighbour. The Fencing Act 1978 sets out how neighbours share the cost of a boundary fence, so talk to them early. A disagreement over a shared fence can delay a job more than the build itself.
When to hire a professional installer
A simple wire mesh fence on level ground, up to about 30 to 40 m, is within reach of a competent DIY owner. For removable panels with gates, precast concrete walls, sloping ground or any work on a shared boundary, a specialist fencing contractor is the safer and often the more economical choice over the life of the fence. A poorly built fence, with posts out of plumb, mesh that is not properly tensioned or a wall without adequate footings, costs more to put right than the labour would have cost in the first place.
Get at least two or three written quotes. Ask each contractor to specify the materials, post count, post spacing, footing method, whether a gate is included, the workmanship warranty and their public liability insurance. Quotes that differ in those details are not directly comparable, so line them up before you choose.
What the calculator leaves out
Gates, including hinges, latches and any automation, are priced separately. So are ground preparation, removal of an old fence, disposal of waste, consent fees and any retaining work. GST may or may not be included in a quote, so check before comparing figures. Add these items to the total yourself, using separate quotes, before you compare the result with a contractor's offer.
Edge cases
A length of zero gives a total cost of zero and a post count of one. That is a result of the formula rather than a real fence, so ignore the post count when the length is zero. A zero labour rate gives the material cost only, and a zero material rate gives the labour cost only. Both rates and the length should be positive in practice, and a negative value has no physical meaning, so enter only positive numbers. A very short section below 2.5 m still needs two posts under this formula, one at each end.
Common mistakes
The most frequent errors are measuring the house wall instead of the boundary line, forgetting the closing post or the gate, mixing up the rates for mesh and panels, comparing a quote that includes posts with one that does not, leaving out ground work, and using a rate from another region. Check each input against the quote it came from. Check the height limit before you choose the fence type, because the wrong height can mean a redesign.
When not to use this calculator
The calculator is for a straight run of ordinary garden or boundary fencing, measured along the actual line. It does not suit retaining walls, hedges or pool barriers, which have their own safety rules. For a complex or irregular site, a visit from a contractor gives a far more reliable figure than any calculator.
Why the output is an estimate
The calculator does not hold a price list. It multiplies the rates you enter, so its accuracy depends entirely on the quotes. Labour rates in particular differ between regions and between one-off jobs and regular contractors. Use the output to plan a budget and to test a quote, not as a fixed price.
Frequently asked questions
How much does a garden fence cost per metre in New Zealand?
The installed cost, meaning material and labour together, depends on the fence type. Wire mesh is usually the least expensive per metre. Timber sits in the middle, and removable steel panels cost more to install. Precast concrete walls cost the most up front. Prices vary by region, supplier, height and site access, so the calculator needs the figures from your own quotes for an accurate result. Enter the material price and labour rate per metre, and the calculator multiplies them by the length to give a total.
Which is the cheapest type of fence for a home garden?
Welded or hexagonal wire mesh is the least expensive option per metre installed. It is simple to put up and needs little upkeep once tensioned, but it gives no privacy. For privacy at a moderate cost, timber is a reasonable choice, though it needs regular treatment or oiling. Removable steel panels and precast concrete walls last longer and need less maintenance, but the initial cost is much higher.
How many posts do I need for a 40 metre fence?
With the 2.5 m spacing the calculator assumes, a 40 m run needs ⌈40 ÷ 2.5⌉ + 1 = 17 posts. That is 16 spans, plus one post to close the run. Taller fences and exposed sites may call for closer spacing, which the calculator does not adjust for, so count those extra posts by hand and price them separately. Posts need footings, so include the cost of concrete and digging in your rate.
Do I need a building consent to put up a fence in New Zealand?
Whether a fence needs a building consent depends on its height, its structure and where it sits. Walls, retaining walls and fences with significant footings or structural parts may need consent under the [Building Act 2004](https://www.building.govt.nz/), which MBIE administers. Your district plan also sets limits on fence height and placement, and these vary by council and zone. Check both with your local council before you order materials. Where the fence is on a shared boundary, the [Fencing Act 1978](https://legislation.govt.nz/act/public/1978/50/en/latest/) also applies to how neighbours share the cost.
Is a timber fence high maintenance?
Yes, more than wire mesh or steel panels. Timber used outdoors needs regular treatment with an exterior oil, stain or varnish. Without it, the timber weathers and decays faster, particularly in damp or coastal areas. Check that the timber is treated for its position, with ground-contact treatment for any posts that go into the soil. Steel panels with an epoxy powder coating need little beyond occasional washing and touch-ups where the coating is chipped.
When should I hire a professional fencing contractor instead of doing it myself?
A competent DIY owner can handle a simple wire mesh fence on level ground of around 30 to 40 metres. Hire a specialist for removable panels with gates, precast concrete walls, sloping ground or work on a shared boundary. A poorly built fence, with posts out of plumb, mesh that is not tensioned or a wall without proper footings, costs more to fix than the labour would have cost. Get at least two or three written quotes that set out the materials, post count, footing method, whether the gate is included and the workmanship warranty.
Does the calculator include gates and ground preparation?
No. Gates, including hinges, latch and any automation, are priced separately. So are ground preparation, removal of an old fence, disposal of waste and any consent fees. Add these to the total yourself, using separate quotes, before you compare the result with a contractor's offer. Check also whether a quote includes GST, since quotes are not always shown on the same basis.
Related calculators
View all Garden, Outdoor & Water calculators →
By RivoCalc · Reviewed under our editorial methodology · Updated 16 May 2026
This calculator gives an estimate only. Actual costs depend on materials, site access, ground conditions, labour rates and council requirements, so get written quotes before you commit.
