Lawn Quantity Calculator: Turf Rolls and Seed
Works out how many turf rolls or kg of lawn seed you need for your garden, with a wastage margin for cuts and an optional material cost estimate.
For a 40 m² garden with a 10% wastage allowance for cuts, the area to cover is 44 m², which means 44 turf rolls of 1 m² each. If you sow seed instead, the same 44 m² at 35 g/m² needs 1.54 kg of seed. The calculator gives both results from the length and width of the area, with the roll area and wastage allowance adjustable.
The area of a turf roll depends on the grower and the cutting machine used, so there is no single standard size. The calculator starts with 1 m² per roll. Check the area on the supplier's data sheet before you order, and change the value in the calculator if the roll is different. Some suppliers sell smaller pieces of turf, and some sell wide rolls for large sites that are laid by machine. Each change in roll area changes the number of units, so compare prices per square metre rather than per roll.
Wastage depends on the shape of the lawn. A simple rectangle with straight edges against a wall or fence loses little to cuts, so 10% is usually enough. Curves, angled corners, garden beds to avoid and paths all add offcuts, so for an irregular garden use 15 to 20%. The allowance is applied to the total area before the roll count is rounded up.
Take the example of a family home with an 80 m² back lawn. With a 10% allowance the area to cover is 88 m², which means 88 rolls of 1 m², or 3.08 kg of seed at 35 g/m². A lawn of the same size in Christchurch, Wellington or Auckland gets the same arithmetic, but the timing of the job and the watering it needs depend on the local climate, as explained below.
The calculator is a quantity tool. It does not decide which product suits your soil or conditions. Enter a price per m² or per kg of seed if you want an estimated material cost, and treat that figure as a planning guide, since prices vary between suppliers and change over time.
The result updates automatically.
10% for simple rectangular areas. 15–20% for irregular shapes with lots of cutting.
Varies by supplier: check the area stated on the product sheet before buying.
Rolls needed
for 88.0 (1 roll)
- Base area
- 80.0 m²
- Area with allowance
- 88.0 m²
- Rolls (1 each)
- 88 rolls
How it works
Formula
How the calculation works
Lawn quantity: how to work out the right amount
Anyone turning a rough garden into a finished lawn faces the same question: how many turf rolls to order, or how much seed to buy? Order too little and you make a second trip to the garden centre, and turf from different deliveries rarely matches exactly in colour. Order too much and the surplus is wasted money. This matters most with turf, which has to be laid soon after it is cut, so the order should match the work you can finish in the same period. Getting the calculation right first time saves time, money and frustration.
The formula: area plus wastage
The starting point is always the area to cover, in square metres. For a rectangular lawn, multiply the length by the width. For irregular shapes, such as curved edges, beds to leave out or obstacles to work around, the most practical method is to sketch the area on squared paper and count the squares, or to split the garden into rectangles and add their areas.
The wastage allowance covers cuts. Straight edges against a wall or fence lose very little, but angles, curves and access areas add up quickly. For simple shapes, such as rectangles or L-shaped lawns, 10% is usually enough. For gardens with curves or many obstacles, raise the allowance to 15 to 20%.
The number of rolls is found by dividing the total area, including wastage, by the area of one roll, and rounding up. Rolls are sold in whole units, so a partial roll has to be bought as a full one. The calculator writes this rounding as the ceiling function in the formula. For seed, the calculator multiplies the total area by 35 g/m², the rate it uses as its default for a new lawn from seed. The seed pack gives the rate for the mix you buy. If it differs, multiply the total area by that rate in g/m² and divide by 1000 to get kilograms. The calculator will not do this for you, so check the packet before ordering.
What is the area of a turf roll?
There is no single standard size. The area of each roll depends on the grower and the cutting machine, so confirm it on the product data sheet or with the seller. The calculator uses 1 m² per roll as its default value, which you can change to match the product you intend to buy.
Roll size changes the unit count considerably. For the same 44 m², 1 m² rolls mean 44 units, while 0.5 m² pieces mean 88. This is why suppliers should be compared by price per square metre, entering the actual area of the product you plan to buy. Wider rolls for large sites are laid by machine, which changes the equipment and labour needed.
Turf or seed?
Turf is the choice for an immediate result. Once it is laid, watered in and has rooted, the lawn can be used again. It is sold at garden centres, turf growers and large DIY retailers, and is often delivered on a pallet. Turf mixes are often based on tall fescue and perennial ryegrass. Ask the supplier which mix is recommended for your region and for the sun and shade in your garden, since the best choice varies between growers. Check the price per square metre at the point of sale before buying.
For an 80 m² lawn with 10% wastage, the area to cover is 88 m², which means 88 rolls of 1 m². Entering the price per m² quoted by the supplier gives an immediate estimate of the material cost, before any work starts.
Seed is usually the lower-cost option in materials, but the lawn takes longer to establish than turf. Quality mixes, usually blends of fine fescue, tall fescue and ryegrass, come in bags of 1 to 5 kg at large DIY retailers and most garden centres. For the same 88 m² at 35 g/m², you need 3.08 kg of seed. Compare the material cost of this quantity with the equivalent turf quote before deciding. Seed also needs more attention: the soil must stay moist through germination, and foot traffic should be kept off the area until the grass is well up.
Common mistakes that cost money
The most frequent mistake is adding no wastage at all. A poorly measured garden bed, a tree in the middle of the lawn or a paved path can throw the whole count out.
The second mistake is comparing prices per roll without checking the area of each roll. Because formats vary between suppliers, a cheaper roll can cost more per square metre. The fair comparison is always per square metre.
The third mistake, specific to seed, is sowing too thickly. Seed applied well above the recommended rate does not give a better cover. The seedlings crowd each other and establish poorly. Follow the rate on the packet, which the calculator's 35 g/m² represents for a new lawn. When overseeding thin patches of an existing lawn, use a lighter rate, following the seed supplier's guidance for renovation work.
Preparing the ground: the step that decides success
For both turf and seed, the result depends largely on soil preparation. The soil should be loosened and levelled to a good depth, and cleared of stones and roots. Heavy clay or compacted soil can be improved by working in coarse sand and a layer of good quality topsoil before the turf or seed goes down. Check how the site drains before laying, and allow for it in the preparation.
Timing depends on the local climate and the season, so the right window varies across New Zealand. Ask your garden centre or turf grower which months suit your region. Laying in summer needs reliable watering, since newly laid turf can dry out quickly. Cold weather can slow root establishment. Check whether your council has water restrictions in place, since these can limit watering in dry periods and affect the planning of a summer installation.
When not to use this calculator
The calculator assumes a reasonably regular area that will be covered entirely with one product. It is not suitable for synthetic turf, which has its own calculation, or for spray-on and hydroseeded systems, where the quantity depends on the product's own instructions. For a patch repair, measure only the damaged area and treat the result as a rough guide, since patches rarely need a full roll or a full sowing rate.
When to hire a professional
For small, flat gardens with well-drained soil, laying turf is a job a careful DIY person can manage. For larger areas, sloping ground, heavy or compacted soils, or gardens with an integrated irrigation system, a landscaper or lawn installer avoids mistakes that are hard to put right later. Labour costs vary with the complexity of the site and the region, so get a quote before deciding between doing the work yourself and hiring someone.
Frequently asked questions
How many turf rolls do I need for 100 m²?
For 100 m² with a 10% wastage allowance, the area to cover is 110 m². With rolls of 1 m², the count is ⌈110 / 1⌉ = 110 rolls. If the garden has many curves or obstacles, a 15% allowance raises the area to 115 m², or 115 rolls. Roll size varies between growers, so check the area on the supplier's data sheet and correct the value in the calculator before ordering.
What is the difference between turf and lawn seed?
Turf is grass already grown on a base and laid straight onto prepared soil. It gives an immediate lawn, which can be used once it has rooted. Seed is generally the lower-cost option in materials, but it is spread over prepared soil and takes longer to germinate and establish. Compare quotes per square metre for both before deciding. Choose turf when you need the lawn sooner and seed when the budget matters more than speed.
What wastage allowance should I use for an irregular garden?
For simple rectangular areas, 10% is enough. For gardens with curves, rounded edges or many obstacles such as beds, trees and paths, use 15 to 20%. Wastage comes from the cuts needed to fit the turf or seed to the edges, so the more irregular the shape, the more cutting and the greater the loss. When in doubt, choose the higher figure, because leftover turf can be used for patching later.
When is the best time to lay turf or sow lawn seed in New Zealand?
The right window depends on your region and the season, so ask your garden centre or turf grower which months suit your area. Laying in summer needs reliable watering, because newly laid turf can dry out quickly. Cold weather can slow root establishment. Local weather varies a lot across the country, so check conditions where you live and whether your council has water restrictions in place before planning the job.
What size is a turf roll, and how many do I need for 50 m²?
Roll size depends on the grower, so confirm it on the product data sheet. The calculator uses 1 m² per roll as its default. For a 50 m² lawn with a 10% allowance, the area to cover is 55 m², which means 55 rolls of 1 m². If the product is sold in 0.5 m² pieces instead, the same area needs 110 pieces. Enter the price per m² from your supplier to estimate the material cost. Installer labour is an extra cost and varies with region and site complexity.
When should I hire a professional for lawn installation?
For small, flat gardens with well-drained soil and no irrigation system, a careful DIY person can lay turf without difficulty. For larger areas, sloping ground, heavy clay or compacted soils, or gardens with an integrated irrigation system, a landscaper or lawn installer is the safer choice. Professional labour costs vary with region and complexity, and that cost is usually small compared with the cost of redoing a poor job.
Related calculators
View all Garden, Outdoor & Water calculators →
By RivoCalc · Reviewed under our editorial methodology · Updated 17 May 2026
Results are planning estimates. Actual roll size, seed rate and coverage vary by supplier, soil and installation method, so check the supplier's data sheet before ordering.
