Pitched Roof Area Calculator
Calculates the true pitched roof area from plan dimensions and roof pitch, for ordering roofing, underlay and capping.
For an 80 m² house footprint with a 35% pitch, the real roof area is about 84.7 m², roughly 4.7 m² more than the plan area. A pitched roof is always larger than the footprint it covers, and the gap grows as the roof gets steeper. This calculator converts the plan length and width into the true roof area, using the trigonometric formula that applies to any roof with a uniform pitch.
Ordering from the footprint is the most common and most costly mistake in roof estimating. At a 30% pitch the roof is 4.4% larger than its plan area, and at 45% it is about 9.7% larger. On a 100 m² plan at 45%, that is roughly 9.7 m² of roofing that a footprint-based order would miss. The usual result is a rushed second order in the middle of the job.
The same formula covers every common roof form. A lean-to roof on a garage, sleepout or extension has one plane. A gable roof, with two planes meeting at a central ridge, is common on New Zealand houses. A hip roof, with four planes that meet at a short ridge, is common too. The area calculation is identical for all three, so you do not need a separate method for each shape.
Enter the lengths in metres and the pitch as a percentage. Pitch is sometimes given in degrees, so check the unit on your plans first: a 30% pitch is about 16.7 degrees, not 30 degrees. The calculator then shows the total pitched area, the pitch factor, the estimated ridge height and, if you need it, the area with a waste allowance.
The result updates automatically.
Parallel to the ridge — eave to eave
Perpendicular to the ridge — eave to eave
30% means it rises 30 cm for every horizontal metre (3.6 in per foot). Typical values: 25 to 45%.
10% for simple roofs; 15% for multiple faces with valleys.
Total sloped area
4.4% more than the plan area of 80.0
Area with a 10% allowance
the quantity to use when ordering materials
- Plan area
- 80.0 m²
- Pitch factor
- ×1.0440
- Ridge height
- 1.20 m
- Increase over the plan area
- +4.4%
How it works
Formula
How the calculation works
How to work out the real area of a roof
A roof is always larger than the footprint of the building it covers. The gap grows with pitch: a 30% roof has about 4.4% more area than its plan footprint, and a 45% roof has about 9.7% more. A roof order based on the floor plan will fall short, especially on steeper roofs. This calculator converts the plan length and width into the true pitched area. It works for any roof where all the planes share the same pitch, whatever the shape.
Why the formula works
Each roof plane is a flat surface tilted at a fixed angle. Its length along the slope is longer than its horizontal run, and the ratio between the two depends only on the pitch. Over a horizontal run of 100 m, a pitch of p% rises p m, so the slope length is √(100² + p²) m. Dividing by 100 gives the factor √(1 + (p/100)²), which is the conversion used in the formula. The factor is always 1 or more, so the pitched area can never be smaller than the plan area.
One factor covers a whole roof because every plane at the same pitch is stretched by the same amount. The true area of a plane equals its plan projection divided by the cosine of its angle, and the projections of all the planes add up to the footprint. Multiplying the footprint by one factor therefore gives the total. This holds for a lean-to, a gable or a hip roof. The shape changes how the footprint is divided into planes, but not the total.
Pitch factors at common values
- 20%: factor 1.020, so the roof is 2.0% larger than the plan area
- 30%: factor 1.044, so the roof is 4.4% larger
- 35%: factor 1.059, so the roof is 5.9% larger
- 45%: factor 1.097, so the roof is 9.7% larger
For an 80 m² footprint at 35%, the pitched area is 80 × 1.059 ≈ 84.7 m². For a 100 m² footprint at 45%, it is about 109.7 m². The increase is not linear with pitch. Moving from 20% to 30% adds about 2.4 percentage points of extra area, while moving from 30% to 45% adds about 5.3 points, so steep roofs need proportionally more material.
Percent is not degrees
Pitch is a ratio of rise to run, expressed as a percentage. A 30% pitch is an angle of about 16.7 degrees, since arctan(0.30) ≈ 16.7°. An angle of 30 degrees, on the other hand, is a pitch of about 57.7%, which is nearly double. Entering a degree value into the percentage field understates the area, and that leads to a short order. A 45 degree roof is exactly 100%. Check which unit your plans use before you enter the number.
Roof shapes and ridge height
- Lean-to (one plane): the height difference between the high and low eave equals the width multiplied by the pitch. A 4 m wide lean-to at 25% has a 1 m difference.
- Gable (two planes): the ridge sits above the eaves by half the width multiplied by the pitch. An 8 m wide house at 35% has a ridge 1.4 m above the eaves.
- Hip (four planes): the ridge is shorter than the building. The area formula still applies, and the ridge height is set by the shorter plan dimension, using the same half-width rule.
Planes with different pitches
The single factor only works when every plane has the same pitch. A roof with a north plane at 35% and a south plane at 20%, for example to suit solar panels, must be split. Calculate each plane separately with its own plan dimensions, then add the results. The calculator takes one pitch for the whole roof, so enter each plane as its own calculation.
Measuring the pitch on an existing roof
Without instruments, place a 300 mm spirit level on the roof and lift one end until the bubble is centred. Measure the height of the lifted end above the roof surface, in millimetres. Divide that height by 300 and multiply by 100 to get the pitch in percent. Plans and truss drawings usually state the pitch, so check those first. Working on a roof is dangerous, so use fall protection or measure from the ground where possible.
Waste allowance
The calculator's figure is the plane area and does not include waste. Cutting at eaves, verges, valleys and hips leaves offcuts that cannot always be reused, so a waste allowance is needed when ordering. A simple gable with few cuts needs less allowance than a hip roof, or a roof with valleys and dormers, where cutting is more frequent. Add the allowance to the pitched area, not to the footprint. Ridge, hip and valley capping are separate lengths, so calculate them from the roof edges rather than from the area. Check the sheet or tile coverage and side lap in the product's installation guide, since these vary by profile.
Common mistakes
- Using the footprint. It is the most frequent and most costly error. Always use the pitched area.
- Applying the factor twice. If you have measured the roof surface directly, that measured area is already the pitched area. Multiplying it by the factor again counts the pitch twice.
- Measuring to the wall, not the eave. Measure from eave to eave, including the overhang, because the roofing covers the overhang too.
- Confusing degrees and percent. A degree value entered as a percentage understates the area, as shown above.
When to bring in a professional
The area calculation is for estimating materials and checking a quote. It does not replace a roof design. For a full re-roof or a new build, a roofer or a Licensed Building Practitioner should check the roof framing and bracing, the underlay, the flashings at the ridge, valleys and eaves, and whether the chosen roofing suits the pitch. For timber-framed houses up to three storeys, NZS 3604:2011 sets the framing rules. Timber framing in older houses should be inspected for rot and borer before any work starts.
Some roof work needs building consent from the local council under the Building Act 2004. Schedule 1 of that Act lists the work that is exempt, so check it, or ask the council, before you start. The Building Code, administered by the Ministry of Business, Innovation and Employment (MBIE), sets weathertightness requirements for roofs under clause E2, External moisture. Properties in heritage areas, or with scheduled heritage features, may face limits on roofing materials or appearance under the district plan. Check the district plan with the council before you order materials.
Frequently asked questions
How do I convert plan area to pitched roof area?
Multiply the plan area by the pitch factor, which is the square root of 1 plus (pitch divided by 100) squared. At 30% the factor is about 1.044, so the pitched area is 4.4% larger. At 45% the factor is about 1.097. Example: an 80 m² footprint at 35% pitch gives 80 × 1.059 ≈ 84.7 m² of roof. Use the pitch in percent, not degrees, and enter the length and width measured on plan, from eave to eave.
Is a percentage pitch the same as an angle in degrees?
No. Pitch in percent is the rise divided by the horizontal run, multiplied by 100. A 30% pitch is an angle of about 16.7 degrees. An angle of 30 degrees is a pitch of about 57.7%, which is nearly double. Plans and specifications may use either unit, so check before entering the value. A 45 degree roof is exactly 100%.
How much bigger is a roof than the house footprint?
It depends on the pitch. At 20% the roof area is about 2.0% larger than the plan area, at 30% about 4.4% larger, and at 45% about 9.7% larger. The increase is not linear, so a steep roof adds proportionally more area than a shallow one. On a 100 m² footprint at 45%, the roof is about 109.7 m².
Does the formula work for hip roofs?
Yes, for any roof where every plane has the same pitch, whether it is a lean-to, a gable or a hip roof. Each plane's pitched area is its plan area divided by the cosine of its angle, and the plan areas add up to the footprint, so one factor covers the whole roof. The ridge height of a hip roof is set by the shorter plan dimension. If the planes have different pitches, calculate each plane separately and add the results.
What do I need to know before ordering roofing materials?
Start from the pitched area, not the footprint. Add a waste allowance, which should be higher for roofs with many hips and valleys. Check the minimum pitch, sheet length and side lap for your chosen profile in the manufacturer's technical data sheet, since these vary between products. Ridge, hip and valley capping are calculated separately from the roof area.
When should I hire a roofer or a Licensed Building Practitioner?
For a full re-roof or a new build, a roofer or Licensed Building Practitioner should check the framing and bracing, underlay, flashings and whether the chosen roofing suits the pitch. For timber-framed houses up to three storeys, NZS 3604:2011 sets the framing rules. Older timber should be inspected for rot and borer before work starts. The area calculation supports quoting and materials checks, but it does not replace a roof design or building consent.
Related calculators
By RivoCalc · Reviewed under our editorial methodology · Updated 12 May 2026
This calculator gives an estimate of roof area for materials planning only. It is not a structural design or a building consent. Check framing, pitch limits and roofing requirements with a qualified roofer, a Licensed Building Practitioner or your local council before you build or re-roof.
