Roof Tile Quantity Calculator: Tiles Needed per m²
Works out how many roof tiles a pitched roof needs, including a waste allowance, for Marseille-profile, pan-and-cover, Roman, flat and custom tiles.
A pitched roof of 120 m², measured along the sloping surface, covered with tiles at an assumed yield of 16 pieces per m² and a 10% waste allowance needs 2,112 tiles. The same roof in pan-and-cover tiles at an assumed yield of 13 pairs per m² needs 1,716 pairs, which is 3,432 individual pieces. The calculator returns this total for any roof area and tile yield you enter.
The tile profile changes the order more than most people expect. Yield per square metre sets how many boxes or pallets you buy, and two profiles on the same roof can need noticeably different piece counts. This calculator covers four common profiles: Marseille, pan-and-cover, Roman and flat tiles. Each has a starting yield filled in. That value is a placeholder, not a product figure, so replace it with the number from your product's technical data sheet. For concrete tiles or any specific product, select Custom and enter that yield.
Use the real sloping area, not the plan area. The plan area is the footprint seen from above, and it is always smaller than the surface the tiles cover. For a 35% pitch (about 19 degrees), the sloping surface is roughly 6% larger than the plan area. Measure each roof plane, add the results and enter the total. The waste allowance covers cut pieces at gables, hips and eaves, along with breakages during delivery and fixing.
The result is an estimate for ordering, not a roof design. It counts field tiles only. Ridge, hip, verge and valley pieces are usually separate products and need their own counts. A weatherboard house in Auckland, a townhouse in Wellington and a rebuild in Christchurch all follow the same arithmetic, but the pitch, the tile profile and local building requirements decide what is practical.
The result updates automatically.
The actual sloped surface area, not the plan (footprint) area
Typical value for the selected roof tile type
10% for simple roofs; 15% for roofs with multiple pitches or complex ridge lines
Check the unit price with your supplier for the model you've chosen
Roof tiles needed
includes 128 pieces of waste allowance
- Roof area
- 80.0 m²
- Coverage rate
- 16 pieces
- Tiles before allowance
- 1,280 pieces
How it works
Formula
How the calculation works
How many roof tiles do you need for a pitched roof?
Working out roof tile quantities before you buy is one of the most useful checks on a re-roof or a new build. Order too few and the job stops partway through while you wait for another delivery. Order a profile that has been discontinued and you may end up with visible differences in colour or texture between batches. The core formula is simple: multiply the roof area by the number of tiles per square metre, then add a waste allowance. The calculator uses exactly this logic and rounds the result up to a whole number. The step most people get wrong is the area, because the footprint of a house on the plan is smaller than the surface the tiles actually cover.
The calculator applies the formula N = ⌈A × r × (1 + D/100)⌉, where N is the total number of tiles, A is the actual roof area, r is the tile yield and D is the waste allowance. Every term is a direct input, so you can check any result by hand with a basic calculator.
Why the sloping area matters
A pitched roof has a larger surface than the area it covers on the plan. The conversion is:
Sloping area = Plan area × √(1 + (pitch in % / 100)²)
At a pitch of 30% (about 17 degrees), the sloping surface is about 4.4% larger than the plan area. At 45% (about 24 degrees) it is about 9.7% larger, and at 50% (about 27 degrees) it is about 11.8% larger. On a plan area of 120 m², that is roughly 5 m² at 30% and 14 m² at 50%. That is enough to leave a short row of tiles unplaced at the bottom of the last course, and it is why using the plan area always leads to an order that is too small.
A worked example: a rectangular roof plane is 10 m long along the eaves and has a horizontal run of 5 m from the eaves to the ridge. At a 35% pitch the rise is 1.75 m, so the length of the slope is the square root of 5 squared plus 1.75 squared, about 5.30 m. The plane therefore covers about 53 m² of surface, not the 50 m² shown on the plan.
Tile profiles and what they change
Four ceramic profiles are covered here, each with a starting yield filled in. That yield is a placeholder to replace with the product figure, because tile dimensions, overlap and product design vary between manufacturers.
- Marseille profile. A single interlocking tile in a rectangular format, with a side lock that makes courses easier to align. It is the most common choice for new builds because it is quick to lay. Take the yield from the data sheet for your product.
- Pan-and-cover (barrel) profile. A two-piece system, with a pan laid hollow side up and a cover over each joint. Laying takes more time, and the yield depends on how far the pieces overlap. This profile suits restorations and buildings where a traditional look is required. Yield is counted in pairs, one pan and one cover, so counting single pieces roughly doubles the figure. Check whether the manufacturer's data sheet counts pairs or single pieces before you enter the yield.
- Roman profile. A format similar to the Marseille tile, with a softer, more rounded look that suits Mediterranean-style houses. Check the yield in the data sheet for the exact product.
- Flat profile. A small, plain format with a traditional appearance. Each piece covers less area, so the piece count per m² is much higher than for the larger profiles. Handling and breakage risk rise with it, so give the waste allowance more attention on this profile.
- Custom. Enter the yield from the manufacturer's data sheet for concrete tiles, for clay tiles from a specific product, or for any other covering.
Waste allowance and rounding
The waste allowance covers three things. The first is cut pieces at the edges, especially at gables, hips, valleys and eaves, where tiles must be trimmed to fit. The second is breakage during transport and fixing. The third is a reserve for future repairs. A simple rectangular roof with no interruptions needs a smaller allowance than a roof with several planes, dormers or a complex hip layout. Choose the percentage by looking at the roof plan, not by applying a fixed rule.
Rounding is applied at the end. Because the result is rounded up to a whole number, the figure is never below the calculated value. Round the order up to the supplier's box or pallet size only after you have the total.
Tiles from different production batches can vary slightly in size, colour and surface glaze. Where possible, buy the full quantity in one batch and keep a few spare pieces from it in storage. Storing spares is far cheaper than trying to match a discontinued profile years later.
Measuring a real roof
Measure each plane separately. The most reliable method for a rectangular plane is to measure the eave length along the bottom edge and the slope length from the ridge to the eaves, then multiply the two. For hips and irregular planes, split the roof into simpler shapes, calculate the area of each and add them. Enter the total as the roof area. Deduct large openings such as skylights from the total, because tiles are not laid over them. The waste allowance covers the cut pieces around the opening.
On a roof you are replacing, a roofer can measure the existing surface directly, which is more accurate than working from old drawings. Drawings often do not match the roof as built.
Pitch, degrees and minimums
The calculator takes pitch as a percentage, but many builders and plans give pitch in degrees. To convert, take the inverse tangent of the percentage divided by 100. A 35% pitch is about 19 degrees. Pitch matters for two reasons. The sloping area grows as the pitch rises, and each profile has a minimum pitch in the manufacturer's data sheet. Below that minimum, water can run back under the tiles and into the roof structure. Check the minimum for the exact product before you commit to a profile, particularly on a low-pitch roof.
Building requirements in New Zealand
Roofing is part of building work regulated under the Building Act 2004 and the New Zealand Building Code, administered by MBIE. Clause E2 (External Moisture) sets the expectation that the roof keeps water out, and its Acceptable Solution E2/AS1 gives acceptable details for roof cladding. Roof framing in timber-framed houses of up to three storeys is covered by NZS 3604:2011. Product definitions for clay roof tiles are set out in the European standard EN 1304, but local authorities may have additional requirements, so confirm them before you order. The New Zealand Building Code information on the MBIE website is the starting point for current clauses.
Whether a re-roof needs building consent depends on its scope, so check with your local council before ordering material. Ask the council, too, whether the property is in a heritage area or is heritage-listed, because this can affect the materials you are allowed to use.
Scenarios
A weatherboard house in Auckland with a simple gable roof is the straightforward case. It has two planes and few interruptions, so a smaller waste allowance is usually enough. A townhouse in Wellington with a hip roof, several planes and a valley needs more planning. Split the roof into planes, measure each one, and allow a larger waste percentage, because the cuts at valleys and hips use more pieces.
A rebuild in Christchurch, where the old roof is being removed, benefits from a site measurement by the roofer, since the existing roof may differ from the drawings. A lifestyle block near Hamilton with a shed or carport needs a separate calculation for each pitched roof, measured on its own planes. A steep roof in Queenstown has a larger sloping area for the same plan footprint, so the pitch correction matters more there.
Common mistakes
- Using the plan area instead of the sloping area. This is the most frequent error and always produces an order that is too small.
- Entering the yield of a different profile from the one being ordered.
- Forgetting that ridge, hip and verge pieces are separate products with their own counts.
- Ordering exactly the calculated number, with no spares for repairs.
- Mixing tiles from different batches on the same roof.
- Ignoring the minimum pitch of the chosen profile.
When not to use this calculator
This calculator counts individual tiles. Long-run metal roofing is measured by sheet length and cover width, so use a sheet calculator for it. The calculator is also not a substitute for a roof design, a structural check, or a decision on a roof with a pitch below the manufacturer's minimum. If the roof also needs insulation under the cladding, calculate that separately.
Frequently asked questions
How many roof tiles do I need for 100 m² of roof?
Multiply the sloping roof area by the tile yield, then add the waste allowance. For 100 m² of sloping surface, an assumed Marseille-profile yield of 16 pieces per m² and a 10% allowance give 100 × 16 × 1.10 = 1,760 tiles. With an assumed pan-and-cover yield of 13 pairs per m², the count is 1,430 pairs, which is 2,860 individual pieces. These figures are for illustration and assume 100 m² of sloping surface, not plan area. Enter your real area and the yield from your tile's data sheet for an exact figure.
How many pan-and-cover tiles per m²?
Pan-and-cover tiles are counted in pairs, one pan and one cover. The yield depends on the product and the overlap used, so there is no single figure for every roof. Use the manufacturer's data sheet, and check whether it counts pairs or single pieces, since counting single pieces roughly doubles the figure. For illustration, a 50 m² sloping roof at an assumed yield of 13 pairs per m² needs 50 × 13 = 650 pairs, plus a 10% waste allowance of 65 pairs, for a total of 715 pairs (1,430 individual pieces).
What is the difference between Marseille and pan-and-cover tiles?
Marseille tiles are single interlocking pieces, so they are quicker to lay and align, which is why they are common on new builds. Pan-and-cover tiles are two-piece barrel profiles. They take more labour per square metre and have a traditional look, so they are often chosen for restorations or to match an existing roof. Choose by appearance, pitch and what the existing roof already uses, then compare installer quotes for each profile.
Should I use the plan area or the sloping area?
Always the sloping area, which is the actual surface covered by tiles. The plan area is always smaller, so using it leads to ordering too few tiles. Convert with: sloping area = plan area × √(1 + (pitch% / 100)²). At a 30% pitch the factor is 1.044, at 45% it is 1.097, and at 50% it is 1.118. For a 60 m² plan area at 45%, the sloping area is about 66 m².
What minimum pitch does each tile profile need?
The minimum pitch depends on the product, so use the manufacturer's data sheet for the profile you choose. Clause E2 of the New Zealand Building Code and its Acceptable Solution E2/AS1 set out requirements for roof cladding, so check them alongside the data sheet. Below the minimum pitch, water can run back under the tiles and into the roof structure. The risk is greatest on low-pitched roofs, so check the pitch before choosing a profile.
Can I mix tiles from different batches on the same roof?
In practice, avoid it. Tiles from different production batches can vary slightly in size, colour and glaze, and the difference often becomes visible after several years of sun and rain. Order the full quantity from one batch where possible, and store a few spare pieces from the same batch. The waste allowance covers cut and broken pieces, but it does not replace matching batches.
When should I hire a roofer?
For a full re-roof or a new build, hire an experienced roofer who works with your tile profile. The calculator helps with budgeting and checking a quote, but it does not replace a roof design. A roofer checks the framing and battens, the underlay, and the flashings at the ridge, hip, valley and eaves. Whether a re-roof needs building consent depends on its scope, so ask your council first. For an older or heritage-listed house, get the structure inspected before any roof work begins.
Related calculators
By RivoCalc · Reviewed under our editorial methodology · Updated 3 June 2026
This calculator gives an estimate to help you order materials. Actual quantities depend on the tile product, roof layout, and cutting and fixing methods. Ridge, hip and verge pieces are not included. For roof structure, cladding and building consent, consult an experienced roofer or a Licensed Building Practitioner (LBP).
