Sand and Cement Calculator for Mortar and Plaster
Calculates the cement bags and sand volume for mortar, plaster or screed from your area, layer thickness and mix ratio.
To plaster 15 m² of interior wall at 15 mm thick with a 1:4 mix, you need about 0.25 m³ of mortar, including the 10% allowance for site wastage. At that mix, roughly 0.20 m³ of the mortar is sand and the remaining 0.05 m³ is cement, which the calculator converts into a whole number of bags.
The mix ratio is the one input that changes the quantities most. It sets the strength of the mortar and is expressed as parts of cement to parts of sand by volume. A 1:4 mix (one part cement to four parts sand) is a common general-purpose choice for interior plaster and for laying bricks and blocks. A 1:3 mix suits external render and wall areas that are often wet, because it is denser and less porous. Where the work is structural or affects an external wall, the mix should follow the specification from the designer or engineer rather than a general rule of thumb.
Whether you are repairing a plaster wall in a townhouse in Wellington or preparing a floor screed for a shed on a lifestyle block near Hamilton, the calculation is the same. Enter the area, the thickness, the mix ratio and the weight of your bag. The calculator returns the number of cement bags, rounded up to a whole bag, and the matching sand volume. If you enter current prices for cement and sand, it also gives an estimated material cost.
The same logic applies to a floor screed. A 5 cm screed over 15 m² needs a much larger volume than a 15 mm plaster coat, so the cement and sand scale up in direct proportion to the thickness. Double-check the thickness before you order, because it scales the result as directly as the area does.
The result updates automatically.
1 cm bedding · 1.5–2 cm render · 4–7 cm screed
A standard bag of cement typically weighs 25 kg.
Bags of cement
for 0.150 m³ of mortar (10% allowance included)
- Mortar volume
- 0.150 m³
- Sand needed
- 0.16 m³
- Safety margin
- 10% included
How it works
Formula
How the calculation works
How to work out sand and cement for mortar
Mortar bonds, levels and protects. It holds bricks or blocks together, gives plaster a flat base, and forms the floor screeds that take tiles or timber. Many small residential jobs in New Zealand mix mortar on site from cement, sand and water in set proportions, while smaller repairs often use a dry premixed product. Working out the quantities before you buy avoids two common problems: ending up with spare cement, which absorbs moisture and loses strength if stored badly, or running short halfway through a plastering session.
What the mix ratio changes
The mix ratio is the proportion of cement to sand, written as parts of cement to parts of sand. On site, builders usually measure by volume with buckets or shovels rather than by weight, so the ratio is a volume ratio. The mixes used most often are:
- 1:3 (one part cement to three parts sand): a richer mix for external render and for areas exposed to water. It contains more cement than a 1:4 mix, which is why it is chosen where more strength or moisture resistance is needed.
- 1:4 (one part cement to four parts sand): a versatile general-purpose mix for laying bricks and blocks, interior plaster and light screeds.
- 1:5 (one part cement to five parts sand): a leaner mix for interior plaster in dry rooms where high strength is not needed.
- 1:6 (one part cement to six parts sand): for infill, levelling and low-stress work.
The New Zealand Building Code, administered by the Ministry of Business, Innovation and Employment (MBIE), sets the performance requirements that masonry and plaster must meet. Clause B1 (Structure) and clause E2 (External moisture) are the most relevant to rendering and masonry, and the Acceptable Solutions describe ways of meeting them. The European standards EN 998-1 (rendering and plastering mortars) and EN 998-2 (masonry mortars) are useful technical references for specifying and testing mortar. They are not New Zealand requirements, and local councils may have additional expectations. Where a structure depends on the mortar, the engineer's specification takes precedence over any general ratio.
A common approach is to start with 1:4 for interior work and move to 1:3 where the wall is exposed to weather or moisture. The calculator uses the cement content for each mix, so changing the ratio changes the result directly.
How to calculate the volume of mortar
The base of the calculation is the volume of the layer, which is the area multiplied by the thickness. For a 15 m² floor with a 5 cm screed, the volume is 15 × 0.05 = 0.75 m³. For the plaster on a wall 3 m wide and 2.5 m high, with a 1.5 cm coat, the area is 7.5 m² and the volume is 7.5 × 0.015 = 0.11 m³, rounded.
The thickness is an input you set for the job, not a fixed value. Take it from the specification for your work or from the product data sheet. The thickness is entered in centimetres because the formula divides it by 100 to convert it to metres. A coat that is too thick is more prone to shrinkage cracking, and a coat that is too thin may not cover the irregularities in the surface.
The calculator adds a fixed 10% allowance to the calculated volume. The reason is practical. The thickness of a plaster coat or a joint is never perfectly even. There are thicker spots, uneven corners and some mortar lost during application. A 10% allowance is usually enough for ordinary work. Very irregular walls or very absorbent surfaces may need more, so order a little extra when the job is awkward.
Valid inputs and edge cases
The area, the thickness and the bag weight must each be a positive number. A bag weight of zero cannot be used, because the formula divides by it. A negative value has no physical meaning for an area, a thickness or a bag weight. If the area is zero, there is no mortar to order and the result is zero bags. Enter the units the calculator expects: square metres for the area, centimetres for the thickness and kilograms for the bag weight. Check the label on the bag, because the weight printed there is the value to enter.
Cement, sand and where to buy them
Cement is sold in bags from builders' merchants, hardware stores and building supply yards. For general mortar, a general-purpose cement is the usual choice. Keep bags dry and off the ground until use, because damp cement sets lumpy and loses strength.
Sand for mortar falls broadly into two types:
- Washed river or plaster sand: fine to medium grain, the usual choice for plaster, brick and block mortar.
- Crushed or manufactured sand: angular particles that give a good mechanical key for external render. It is often used where the surface is exposed to the weather.
For larger volumes, bulk sand from a local aggregate supplier is usually more economical than bagged sand. Bagged dry premixed mortar avoids the mixing, but it costs substantially more per cubic metre than mixing cement and sand on site. For a small repair, the convenience may be worth it. For a whole room, mixing on site is almost always the better value. Enter current prices in the price fields to see the estimated material cost.
Common mistakes to avoid
Mixing up volume and weight ratios. Site ratios are volumetric. Some technical data sheets give mix proportions by weight, because cement is denser than loose sand. Check which basis a data sheet uses before following it.
Using dirty or fine-heavy sand. Sand with a lot of silt or clay in it needs noticeably more cement to reach the same strength. Quarry sand can carry more fines than washed river sand, so ask the supplier where the sand comes from and how it is graded. For a large job, test a small batch first.
Adding too much water. A very wet mortar is easier to spread but loses strength significantly. Use the least water that still lets you work the mix. A good mortar holds its shape on the trowel and does not slump off the board.
Not curing the surface. Cement mortar needs moisture to gain strength. On hot, dry or windy days, such as a nor'wester in Canterbury, mist the surface with water for several days after application. This reduces drying shrinkage and the cracks that come with it.
When to use this calculator, and when not to
The calculator suits simple plaster on masonry walls, brick or block laying for internal partitions, repairs, and small floor screeds. In New Zealand, many interior walls are lined with plasterboard rather than cement plaster, so the calculator is most useful for masonry, exterior render, repairs and screeds.
It is not a substitute for an engineer where a structure is involved, or for advice on an external wall. Persistent water ingress, rising damp or cracking that keeps returning should be investigated before any new render is applied, because a new surface will not fix the cause. Under the Building Act 2004, many alterations need a building consent from the local council. Work on structural elements or external cladding should be checked by a suitably qualified professional, such as a chartered professional engineer or a licensed building practitioner.
The result is an estimate for planning and ordering. Keep a small margin for the things you cannot control on site, and confirm the mix against the product data sheet and the requirements that apply to your building.
Frequently asked questions
How many bags of cement do I need to plaster 10 m²?
For 10 m² of wall at 15 mm thick with a 1:4 mix, the mortar volume is 0.15 m³, or 0.165 m³ with the 10% allowance for site wastage. In a 1:4 mix, sand makes up about four-fifths of the volume and cement about one-fifth, so the sand needed is roughly 0.13 m³. The number of cement bags depends on the cement content of the mix, which the calculator applies for you. Enter your bag weight, and the result is rounded up to whole bags.
What mix ratio should I use for laying bricks or blocks?
A 1:4 mix (one part cement to four parts sand by volume) is a common starting point for laying bricks and blocks in dry internal walls. For external walls, or walls exposed to rain and moisture, a 1:3 mix is more usual because it contains more cement and is less porous. Joint thickness should follow the specification for the brick or block system you are using. Where a structural wall or an engineer's specification is involved, follow the specified mortar rather than a general ratio.
What is the difference between mortar and concrete?
Mortar is a mix of cement, sand and water with no coarse aggregate. It is used for plaster, for joints between bricks or blocks, and for floor screeds. Concrete adds coarse aggregate, such as gravel or crushed stone, which gives it higher compressive strength. Concrete is the material for structural elements such as slabs, footings, columns and beams. In short, mortar is for finishing and masonry, and concrete is for structure.
When should I use a 1:3 mix instead of 1:4?
A 1:3 mix is stronger and less porous, so it suits external render exposed to rain, wet areas such as bathrooms and laundries, and garden walls in contact with wet soil. A 1:4 mix covers most interior plaster and brick or block laying in dry conditions. Where the wall is part of a structure or sits in a particularly exposed site, check the mix with the designer.
When is a dry premixed mortar bag better than mixing on site?
Dry premixed mortar bags suit small repairs where you have no mixer, or where you want a factory-controlled mix for a short job. They cost substantially more per cubic metre than mixing cement and sand on site, so for larger jobs, mixing on site is usually more economical. Check current prices at local builders' merchants and enter them in the calculator to compare the costs.
How thick should cement plaster be?
The right thickness depends on the surface, the substrate and the system specified for the job, so no single figure applies everywhere. Thicker coats are more prone to shrinkage cracking, so the product data sheet and the specification set the maximum build for the material you use, and the calculator takes whatever thickness you enter. In New Zealand, plasterboard is the usual lining for most interior walls, so cement plaster is mainly used for masonry, exterior render and repairs. Check the specification for any structural or external wall before you start.
When should I involve a professional for mortar work?
Simple interior plaster and small internal brick or block partitions are suitable for DIY with this calculator. Get advice from a suitably qualified person for external cladding or render on a house, walls with persistent water ingress, rising damp, or any structural wall. Under the Building Act 2004, many alterations need a building consent from your local council, and the work must comply with the New Zealand Building Code. Licensed building practitioners and chartered professional engineers can advise on what applies to your job.
Related calculators
Brick Quantity Calculator for Walls
Works out the number of bricks or concrete blocks a wall needs, with mortar joint thickness and a waste allowance included.
Cement Bag Calculator for Concrete
Calculates the bags of cement needed for a concrete pour from its volume, the mix and the bag weight, with a 5% waste allowance.
View all Structure & Materials calculators →
By RivoCalc · Reviewed under our editorial methodology · Updated 3 June 2026
The results are estimates for planning and ordering only. Actual quantities depend on the mix, the moisture and grading of the sand, site wastage and the product data sheet. Check the New Zealand Building Code and local council requirements before work that needs a building consent or affects a structural or external wall.
