Skip to main content

Garden Fence Cost Calculator (Singapore)

Estimates the installed cost of a garden fence per metre in Singapore, for wire mesh, steel panels, timber or precast walls.

For a landed house on a 10 m × 8 m plot in Bishan, the perimeter to fence is 36 m. A 1.2 m galvanised wire mesh fence along that length needs 16 posts at the calculator's standard 2.5 m spacing: 36 ÷ 2.5 is 14.4, rounded up to 15 spaces, plus one final post.

The total cost is the fence length multiplied by the combined material and labour rate per metre. The post count does not change that sum, but it is the quantity to check against your quote, because posts, footings and concreting are often included in the per-metre rate. A quote that shows materials and labour as separate lines is easier to compare than a single lump sum.

This calculator estimates the cost from the length to be fenced, the fence type and the rates you enter. It covers four common options: galvanised wire mesh, powder-coated steel panels, timber and precast concrete walls. The result is only as good as the rates behind it, so use figures from written quotes wherever you have them, and general estimates where you do not.

Singapore's climate shapes the choice. Heavy rain, high humidity and salt-laden air near the coast speed up corrosion in untreated steel and rot in unprotected timber. Hot-dip galvanising or powder coating for steel, and treated timber rated for exterior use, are the usual protections. On a landed property the fence also marks the boundary line, so its position should be confirmed before any work starts.

The result updates automatically.

Add up all the sections. For a 10 m × 8 m garden, the perimeter is 36 m.

This automatically updates the reference prices. Adjust to match the quote you've received.

Reference value for this type of fencing. Adjust to match the quote you've received.

Enter 0 to see the material cost only.

Estimated total cost

$800.00

For 40 of fencing

Material cost

$400.00

40 × $10.00 per unit length

Labour cost

$400.00

40 × $10.00 per unit length

Total length
40
Estimated posts (every 2.5 m / 8.2 ft)
17
Material cost
$400.00
Labour cost
$400.00
Total cost
$800.00

Turn this calculation into a quote for your client

We're building a tool for professionals. Be among the first to try it.

Share

How it works

1

Enter the total length to fence in metres, adding up every section of the boundary.

2

Choose the fence type: wire mesh, steel panels, timber or precast concrete wall.

3

Adjust the material rate per metre if you have a written quote from a supplier.

Formula

C_total = L × (p_m + p_lab) | N_posts = ⌈L / 2,5⌉ + 1
C_total — Estimated total installed cost (Singapore dollars)
L — Linear length of fence to be installed (m)
p_m — Material price per linear metre (Singapore dollars per m)
p_lab — Labour cost per linear metre (Singapore dollars per m)
N_posts — Number of posts, at a standard spacing of 2.5 m between posts
⌈⌉ — Rounded up to the next whole number, as fencing is bought in whole units

How the calculation works

Garden fence: how to calculate the cost in Singapore

A new fence defines the boundary of a property, changes how a house looks from the outside and gives privacy. The cost per metre depends a great deal on the type chosen, because galvanised wire mesh, powder-coated steel panels, timber and precast concrete walls each combine different materials, posts, footings and labour. Anyone who asks for quotes without understanding what makes up the rate is at a disadvantage, since two offers can look similar per metre while covering very different work. The choice of fence type is not only aesthetic. It reflects durability, maintenance and installation cost over many years.

The calculation itself is direct. The total length of boundary to be fenced is multiplied by the combined rate per metre for materials and labour, and this calculator carries out that step. The result is only as accurate as the rates entered, so use figures from written quotes or current supplier price lists for your area wherever you have them, and treat any default figure as a starting point only.

What makes up the rate per metre

A rate per metre is built from several elements, and it helps to understand each one before comparing offers:

  • Fence panels or mesh, which are the main material item and are priced by length or by panel.
  • Posts, whose number follows from the length and the spacing, with each post needing a footing.
  • Footings and concreting, which some quotes show as a separate line and others include in the rate.
  • Gates and openings, which are normally priced apart from the run of fencing.
  • Labour, covering the time to set out, dig, fix, tension or erect the fence. It rises with slope, poor access and the number of corners.
  • Site conditions, such as uneven ground, overgrown vegetation or work near drains, which affect both materials and time.

The same length can therefore produce quite different totals depending on what each quote includes. Read every line before deciding which offer is the true comparison.

Fence types and what each one involves

Galvanised wire mesh is a simple, lightweight option and a common choice for back gardens, side boundaries and rural or semi-rural plots. Welded or hexagonal mesh rolls in hot-dip galvanised steel, usually 1 m high, are widely available from fencing suppliers. Hot-dip galvanising to ISO 1461 gives the coating its corrosion resistance, which matters in Singapore's humid climate. Installation needs galvanised steel posts set at regular intervals, and the mesh must be tensioned with wire or clips. Posts and tensioning are the lines that differ most between installers, so check them in each quote.

Powder-coated steel panels suit landed houses where the fence forms part of the frontage, and they are often chosen together with a matching gate. The panels are made from electro-welded steel bar with an epoxy powder coating and are commonly about 1.5 m high. They need little maintenance beyond occasional cleaning and touch-up, but they need posts and foundations suited to their height and weight, so the installation details matter as much as the panel itself.

Timber fences, with vertical or horizontal boards on posts, suit a natural garden style and offer good privacy. Treated softwood rated for exterior use and hardwood are the usual choices. Timber needs regular exterior treatment with stain, varnish or a suitable preservative. Singapore's humidity and heavy rain speed up weathering and decay, so this maintenance recurs and should be counted in any whole-life comparison.

Precast concrete walls give full visual privacy and a robust barrier, with very low maintenance once built. Panels of about 1 m in height, in smooth or textured finish, need posts or piers and a foundation, so installation adds to the material cost. This is also the least flexible option if the boundary needs to change later, which is worth weighing against its durability.

Posts and spacing

For wire mesh and timber fences, post spacing affects both solidity and appearance. This calculator uses a standard spacing of 2.5 m between posts as a planning assumption. Taller fences, exposed sites and sloping ground may call for a different spacing, and the spacing actually specified should follow the installer's design and the fitting instructions for the product chosen.

The number of posts follows from the length. Divide the length by the spacing, round up to a whole number of spaces and add one final post. For a 40 m run at 2.5 m spacing, that gives 17 posts. If the installer specifies 2 m spacing for the same run, the count rises to 21, so always confirm which spacing a quote assumes.

Installers often quote a rate per metre with posts included. Confirm exactly what is included before comparing offers, and check the post count against the length so that the quote does not omit posts at the ends or corners.

What sits outside the per-metre rate

Gates and doors are normally not included in the cost per metre and are quoted as separate items. A pedestrian gate with latch and hinges, a vehicle gate for car access and any automation each carry their own quote and add to the fence cost. Site preparation, such as setting out the line, digging post holes and levelling the ground, is often billed separately. On uneven ground with a significant slope, that extra work can be material and should be requested in the quote.

Removal of an existing fence, clearing overgrown vegetation and any work near drains or shared boundaries are also commonly outside the basic per-metre figure. Ask for each of these to be listed separately.

Regulations and boundary rules

Fence height, its position on the boundary and works near drains, road reserves or neighbouring land are governed by planning and building requirements. In Singapore, the Urban Redevelopment Authority (URA) handles planning matters, and the Building and Construction Authority (BCA) administers building control under the Building Control Act and the BCA Approved Documents. Whether approval is needed depends on the height, position and type of fence, the zoning of the lot, and whether the works affect a shared boundary or a drain. Requirements change over time, so confirm the current position with these authorities before ordering material.

The calculator does not check compliance. It only estimates the cost of the fence you specify.

When to hire a professional installer

A simple wire mesh fence on a short, straight run of level ground is a manageable project for an experienced DIY enthusiast. Steel panel fences with gates, precast walls, sloping ground or work along a shared boundary with neighbours are better handled by a specialist installer. Get two or three quotes that specify materials, number of posts, fixing method and workmanship warranty, and check the contractor's registration and credentials for the type of work. A poorly installed fence, with posts out of plumb, mesh badly tensioned or a wall without adequate footings, is usually more costly to put right than the professional labour saved.

Common mistakes

  • Comparing quotes with different scopes, where one includes posts and footings and another does not.
  • Forgetting gates, site preparation, removal of the old fence or clearance work.
  • Measuring the whole plot instead of the length actually to be fenced, which matters where part of a boundary is already shared or walled.
  • Applying a rate from one fence type to another, for example timber labour rates to steel panels.
  • Ignoring slope. A fence line on a slope needs stepped or raked panels, which changes both the material and the labour.
  • Treating timber as a one-off purchase. Its maintenance cost recurs for as long as the fence stands.

Edge cases in the calculation

A zero length gives a zero result. A zero material rate returns the labour cost alone, and a zero labour rate returns the material cost alone, which is useful for checking a supplier figure. A negative length or rate has no physical meaning and should be corrected before the result is used. The post count uses the standard spacing of 2.5 m, so for taller fences or exposed sites, recalculate the count by hand at the spacing the installer specifies.

When not to use this calculator

The calculator does not size structural retaining walls, load-bearing boundary walls or fences that carry the weight of a gate. Those need an engineer or an installer with relevant experience. It does not replace a site visit where ground conditions are unstable or where drainage works are needed.

Reading the formula

The cost is calculated as C_total = L × (p_m + p_lab), where L is the length, p_m is the material rate per metre and p_lab is the labour rate per metre. The post count is N_posts = ⌈L ÷ 2.5⌉ + 1, where the ceiling function rounds the spaces up to a whole number before the final post is added. Keep the rates in Singapore dollars per metre and the length in metres. The result is a planning figure, not a fixed quotation.

Frequently asked questions

How much does a garden fence cost per metre in Singapore?

The installed cost depends on the fence type, the length, the site and the contractor, so no single figure applies to every garden. Each type brings a different mix of materials, posts, footings and labour, and the total per metre changes with slope, access and any gates or site preparation. The most reliable figure comes from written quotes for the same length and specification. Enter the material and labour rates from those quotes into the calculator to see the total for your boundary, and compare quotes that set out the scope in the same way.

Which fence type suits a budget-conscious garden?

The answer depends on the quotes you receive, because the rate per metre changes with the site and the installer. Galvanised wire mesh is generally the lightest and simplest type to fit, which is why it is a common starting point for back gardens and side boundaries where privacy matters less. Timber gives more visual privacy but needs regular exterior treatment against humidity and rain. Powder-coated steel panels and precast concrete walls usually need less routine attention, although their installation is more involved. Compare the total cost over the years you expect to keep the fence, not only the price on the day of installation.

How many posts do I need for a 40 m fence?

At the calculator's standard spacing of 2.5 m between posts, a 40 m run needs ⌈40 / 2.5⌉ + 1 = 17 posts, which is 16 spaces plus one post to close the run. If the installer specifies a different spacing, for example because of a taller fence or an exposed site, use the same method with that spacing. At 2 m spacing, the same 40 m needs 21 posts. Galvanised steel posts are a common choice for wire mesh, and each post needs a footing, so include the cost of fixing them in the budget. The calculator uses 2.5 m automatically when it counts posts, so recalculate by hand if your design needs a different spacing.

Do I need approval to put up a fence in Singapore?

It depends on the fence and the property. Approval may be needed where the height, position or type of fence is subject to planning or building requirements, or where the works affect a shared boundary, a drain or a road reserve. The Urban Redevelopment Authority (URA) handles planning matters, and the Building and Construction Authority (BCA) administers building control under the Building Control Act. Because requirements depend on the specific lot and the work proposed, check with these authorities before ordering materials. Confirming this first avoids having to alter or remove a fence after installation.

Does a timber fence need much maintenance?

Yes. Timber left untreated weathers and decays quickly, and Singapore's humidity and heavy rain increase that risk. A timber fence should be treated regularly with exterior stain, varnish or a suitable wood preservative, and the surface should be checked for rot, loose boards and fixings. Treated softwood rated for exterior use or durable hardwood resists decay better than untreated wood, but it still needs periodic care. By comparison, powder-coated steel panels need only occasional cleaning and touch-up, and precast concrete walls need little attention once built. Include the recurring cost of timber treatment when comparing whole-life costs, not only the first installation price.

When should I hire a professional installer instead of doing it myself?

A simple wire mesh fence on a short, straight run of level ground is a manageable project for an experienced DIY enthusiast. A professional installer is the safer choice for powder-coated steel panels with gates, precast concrete walls, sloping ground or work along a shared boundary with neighbours. Ask for two or three quotes that set out the materials, post count, fixing method and workmanship warranty, and check the contractor's registration and credentials for the works. A poorly installed fence, with posts out of plumb or a wall without adequate footings, is usually more costly to put right than the professional labour saved.

Related calculators

View all Garden, Outdoor & Water calculators →

By RivoCalc · Reviewed under our editorial methodology · Updated 16 May 2026

The results are estimates for planning purposes only. Real costs vary with material grade, site conditions, access, the contractor and the scope of work. Confirm fence height, boundary position and approval requirements with the relevant authorities before ordering, and obtain itemised written quotes.