Roof Area Calculator for Sloped Roofs
Calculates the true sloped area of a roof from its plan dimensions and pitch, for ordering tiles, membrane and other roofing materials.
For a roof with an 80 m² plan area and a 35% pitch, the true sloped area is about 84.8 m², or 4.8 m² more than the footprint suggests. The multiplier is 1.0595. Order roofing materials from the sloped area, not the plan area, or the order will come up short.
Ordering from the floor plan is the most common and most expensive mistake in roof work. The gap grows with pitch, and not in a straight line. At 20% the sloped area is 2.0% larger than the plan area, at 30% it is 4.4% larger, and at 45% it is 9.7% larger. Pitch is the rise over the horizontal run, expressed in percent, so a 30% roof climbs 30 cm for every metre measured across the plan.
This calculator converts the plan length and width into the true sloped area, using the trigonometric relation that holds for any roof with a uniform pitch. It covers the three forms common on landed houses in Singapore: the single-pitch roof over an extension or carport, the gable roof with two slopes, and the hipped roof with four slopes. Enter the length and width in plan, the pitch in percent and the number of roof slopes. The calculator then shows the sloped area, the pitch factor, the estimated ridge height and, if needed, the area with a waste allowance for ordering.
Most HDB blocks have flat roofs, so the calculator is mainly useful for landed houses, pitched extensions, carports and sheds. A semi-detached landed house in Bishan with a pitched rear extension is a typical case: the extension roof is measured in plan, the pitch is checked, and the materials are ordered from the sloped figure.
The result updates automatically.
Parallel to the ridge — eave to eave
Perpendicular to the ridge — eave to eave
30% means it rises 30 cm for every horizontal metre (3.6 in per foot). Typical values: 25 to 45%.
10% for simple roofs; 15% for multiple faces with valleys.
Total sloped area
4.4% more than the plan area of 80.0
Area with a 10% allowance
the quantity to use when ordering materials
- Plan area
- 80.0 m²
- Pitch factor
- ×1.0440
- Ridge height
- 1.20 m
- Increase over the plan area
- +4.4%
How it works
Formula
How the calculation works
How to calculate roof area in Singapore
The area of a roof is never equal to the floor area of the house. The plan footprint only shows the horizontal projection of the roof, while the real roof surface rises above it and is always larger. The difference grows with the pitch. At a 20% pitch the sloped area is 2.0% larger than the plan area, at 30% it is 4.4% larger, and at 45% it is 9.7% larger. On a roof with 100 m² in plan, that is about 2 m², 4.4 m² and 9.7 m² of extra surface respectively.
The relation follows directly from Pythagoras applied to a sloping plane. For a pitch p in percent, the roof rises p/100 metres for every metre of horizontal run. The sloped length of that strip is therefore √(1 + (p/100)²) metres for each metre of plan. This is the conversion factor used in this calculator. Multiplying the plan length by the plan width and by this factor gives the true sloped area: A = L × W × √(1 + (p/100)²).
Why the same formula works for single-pitch, gable and hipped roofs
Any roof in which all planes share the same pitch has a total sloped area equal to the plan area multiplied by this factor. Each plane is tilted at the same angle, so its true area is its projected area divided by the cosine of that angle. The projected areas of all the planes add up to the plan area of the building, so the factor applies to the whole roof. The hipped ends have triangular planes, but they are tilted at the same angle and contribute in the same proportion. The formula only needs to change when different planes have different pitches. In that case, calculate each plane on its own and add the results.
The three roof forms on Singapore landed houses
A single-pitch roof has one plane sloping from a higher edge down to a lower one. It is common over carports, rear extensions and sheds. The height difference between the high and low edges equals the plan width multiplied by the pitch. For a 4 m wide carport roof at 25%, that difference is 1 m.
A gable roof, also called a dual-pitch roof, has two planes meeting at a central ridge. The ridge height above the eaves is half the plan width multiplied by the pitch. For an 8 m wide house at 35%, the ridge sits 1.4 m above the eaves.
A hipped roof has four planes, with the two end planes forming triangles that meet the ridge. The ridge length is the plan length minus the plan width, and the ridge height is set by the shorter dimension, using the same half-width rule. This form is found on some landed houses and bungalows.
Pitch on Singapore roofs
Singapore has a tropical climate with heavy downpours, and that shapes how a roof should be detailed. Water must run off quickly and cleanly. A low pitch increases the risk of water being driven under tile laps or sheet joints during heavy rain, so pitch matters for leak prevention as well as for the area. Check the minimum pitch in the technical data sheet of the chosen product before ordering. A roof built below that minimum may need a different covering or a change to the design.
Pitch is measured in percent, the rise divided by the horizontal run multiplied by 100. To check the pitch of an existing roof without instruments, place a 30 cm spirit level on the surface, lift one end until the bubble is centred, and measure the gap between the raised end and the surface. Divide that gap by 30 and multiply by 100.
Common mistakes
The most frequent and most costly mistake is to use the plan area as the roof area. For a roof with 80 m² in plan and a 30% pitch, the sloped area is 83.5 m². Ordering for 80 m² leaves about 3.5 m² uncovered, and that shortfall can delay the job while more material is sourced.
The second mistake is confusing percent with degrees. A 30 degree angle is a pitch of 57.7%, nearly twice as steep. Entering a 30 degree angle as 30% understates the slope and the area. Check the unit on the drawing before entering the value.
The third mistake is applying the factor to a surface measurement. If you measure the length of each slope along the roof surface, you already have the sloped dimension, and the area is the sloped length multiplied by the width, with no conversion factor. Use the measured value directly. This calculator takes plan dimensions, so it is the wrong tool for a surface measurement.
Waste allowance and ordering
The sloped area is the basis for ordering, but it is not the final order quantity. Cuts at hips, valleys, verges and around vents and skylights leave offcuts that cannot always be reused. The waste allowance should be higher for roofs with several slopes, valleys and hips, because each junction creates more cuts. Your roofing contractor should confirm the final percentage, since it depends on the product's cover width and the installation method.
Local rules and approvals
Works on a roof, especially those that change the structure or the external appearance of a building, may need approval before work starts. Check the requirements for your own property with the relevant authority, rather than relying on general statements.
Structural checks, including wind uplift on the roof covering, are carried out to the Eurocodes with the Singapore National Annexes (SS EN 1990 to 1999). For clay roofing tiles, the European product standard EN 1304 sets out the definitions and specifications, and manufacturers publish their own installation data for each product.
Older buildings and existing roofs
In older buildings, inspect the roof timber or steel before replacing the covering. Look for rot, corrosion, termite damage and any sag in the rafters or purlins. A new covering adds weight, and a degraded structure may not carry it safely. For this reason, a structural assessment should come before ordering materials for a re-roof.
When to use this calculator and when not to
Use the calculator to estimate roof area for budgeting, to plan the quantities of covering, underlay, insulation, battens, gutters and ridge pieces, and to check contractors' quotes. Do not use it as a structural design, to size rafters, or to confirm wind or load resistance. Flat roofs, such as those on most HDB blocks, do not need this calculation, because their pitch is effectively zero and the factor is 1.
For a full re-roof or a new roof, a registered professional engineer should check the structure, the pitch against the chosen covering, the underlay or membrane, and the detailing at ridges, hips, valleys and eaves. The calculator gives the area that those decisions depend on, but it does not make them.
Frequently asked questions
How do I convert plan area to sloped roof area?
Multiply the plan area by the factor √(1 + (pitch/100)²). For a 30% pitch the factor is √1.09 ≈ 1.044, so the sloped area is 4.4% larger. For 45% the factor is about 1.097, or 9.7% more. Example: a roof with an 80 m² plan area and a 35% pitch has a sloped area of 80 × 1.0595 ≈ 84.8 m².
What is the difference between pitch in percent and an angle in degrees?
Pitch in percent is the rise divided by the horizontal run, multiplied by 100. An angle of 30 degrees is a pitch of tan(30°) × 100 ≈ 57.7%, nearly twice as steep as a 30% pitch. A 30% pitch corresponds to an angle of about 16.7 degrees. Some drawings give angles, so check the unit before entering the value. Entering 30 degrees as 30% understates the slope and the roof area.
How much does a 30% pitch increase the roof area?
At 30% pitch the sloped area is 4.4% larger than the plan area. A roof with 100 m² in plan has a sloped area of about 104.4 m². At 45% the increase is 9.7%, giving about 109.7 m², and at 20% it is only 2.0%, about 102.0 m². The increase is not linear because the factor depends on the square of the pitch, so it accelerates as the roof gets steeper.
Does the formula work for hipped roofs with four slopes?
Yes. For any roof where all planes share the same pitch, the total sloped area equals the plan area multiplied by the factor, whether the roof is single-pitch, gable or hipped. Each plane is tilted at the same angle, so its true area is its projected area divided by the cosine of that angle, and the projected areas add up to the plan area. The formula only needs changing when planes have different pitches. In that case, calculate each plane separately and add the results.
Why does the exact roof area matter when ordering?
The sloped area is the base for tiles, underlay or membrane, insulation, battens, gutters and ridge pieces. Ordering from the plan area leads to a shortfall, which can force an urgent order during the job. A later batch may also differ slightly in shade or size from the first, so it is better to order the full quantity at once. Ask your roofing contractor to confirm the sloped area and waste allowance in writing before ordering.
When should I hire a roofing contractor or structural engineer?
For a full re-roof or a new roof, the area calculation is a budgeting step, not a design. A registered professional engineer checks the roof structure, including rafters, purlins and wall plates, the pitch against the chosen covering, the underlay or membrane, and the detailing at ridges, hips, valleys and eaves. In older buildings, inspect the timber or steel for rot, corrosion or termite damage before any work starts.
Related calculators
By RivoCalc · Reviewed under our editorial methodology · Updated 12 May 2026
This calculator gives an estimate of roof area for ordering materials. It is not a structural design. Final quantities depend on the roof layout, the product specification and the installer's cutting allowance, so confirm them with a registered professional engineer or your roofing contractor before ordering or building.
